JVC SP-D302 manual Standard Recording

Page 23

CAUTION: If recordings you have made have excessive noise or static, the Unit may be too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the System.

Standard Recording

This is the basic method for recording any source. The System also has special ways for recording CD to tape, and tape to tape, which save you time and effort, as well as give you some special effects. However, when you need to add a selection to a tape you have made, or are combining selections from several sources on one tape, use the method described below; just substitute the source you want into this procedure, such as a CD or the Tuner. You can also record from auxiliary source with this procedure.

Using the Unit

1.Insert a blank or erasable tape into Deck B.

2.Press the REVERSE MODE button if you want to record on both sides of the tape.

Press the button until the “ ” or “ ” indicator is lit.

•When using the auto reverse mode, insert the tape so that it will be recorded in the forward (3) direction.

3.Check the recording direction for the tape.

Check that the Tape Direction indicator is the same as that for the tape in the tape deck. If the directions are different, press the 7STOP button after pressing the TAPE ª £ button to set the tape direction.

•When using the auto reverse mode to record both sides of a tape, check that the Tape Direction indicator is in the forward (3) direction. If the direction indicator is not in the forward (3) direction, press the TAPE ª £ button then press the 7STOP button.

4.Prepare the source, for example, by tuning in a radio station, load- ing CDs, or turning on connected equipment.

5. Press the REC START/STOP button.

The REC indicator lights up and the System begins recording.

Using the Remote Control

1.Insert a blank or erasable tape into Deck B.

2.Press the REVERSE MODE button on the Unit if you want to record on both sides of the tape.

Press the button until the “ ” or “ ” indicator is lit.

•When using the auto reverse mode, insert the tape so that it will be recorded in the forward (3) direction.

3.Prepare the source, for example, by tuning in a radio station, load- ing CDs, or turning on connected equipment.

REC PAUSE

4. Press the REC PAUSE ¦ button.

The REC indicator blinks.

5. Press the ª or £ button.

Recording starts in the direction of the button pressed.

The REC indicator stops blinking and remains lit.

•When using the auto reverse mode to record both sides of a tape, press the £ button.

Notes for using Reverse Mode for recording

When recording in Reverse Mode, the System automatically stops when it reaches the end of the reverse (2) direction. To record on both sides of a tape, make sure that the recording direction for the tape inserted into Deck B is forward (3), and that the Tape Direction indicator is also forward (3), before you start recording.

To Pause at Any Time During the Recording Process

Press the REC PAUSE ¦button on the Remote Control. Then press either the ªor £ button on the Remote Control or REC START/STOP button on the Unit to restart recording.

To Stop at Any Time During the Recording Process

Press the REC START/STOP button on the Unit again, or press the 7 button on the Remote Control.

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents MX-D302T Important for Laser Products How This Manual Is Organized FeaturesInstallation of the Unit Power cordTable of Contents Getting Started AccessoriesHow to Put Batteries in the Remote Control Using the Remote ControlUsing an FM 75-Ohm Antenna Cable not supplied Connecting the FM AntennaConnecting the AM Antenna Using the Supplied Wire AntennaRight Speaker Connecting the SpeakersConnecting Auxiliary Equipment VCR or other equipmentOn the Unit On the Remote ControlTurning the System On Turning the Power On and OffCommon Operations DisplaySound Modes Adjusting the VolumeReinforcing the Bass Sound Listening to Auxiliary Equipment Set the Volume control to Press the AUX buttonOne Touch Radio Using the TunerTuning In a Station Switching between Frequency BandsThree Ways to Select a Station Presetting StationsChanging the FM Reception Mode CD £/8 Using the CD PlayerDisc indicators Place a CD, with its label side up, onto the tray For Normal Play Play mode indicator is not litLoading Discs Quickest Way to Start a CD Is with the One Touch OperationSelecting a Disc, Track Or Passage Within a Track Basics of Using the CD Player Normal PlayLocating a Track With the Remote Control Directly Playing a DiscProgramming the Playing Order of the Tracks Continuous PlayPress the £/8 button Random PlayPress the Random button Unlocking the Trays Repeating a Selection or the DiscsTray Lock Function Locking the TraysPress the 0 button for the deck you want to use Using the Cassette DeckRegular Play One Touch PlayFinding the Beginning of the Current Selection Reverse ModeMusic Scan Fast Left And Fast RightThings to Know before You Start Recording RecordingStandard Recording Recording AM Station to Tape How to Use the Dubbing ButtonCD Direct Recording Tape to Tape Recording DubbingPress the Select 5 + or 4 button to set the time Using the TimerSetting the Clock Press the Shift button Press the 1 Clock buttonPress the Select 5 + or 4 button to select the source Setting the TimerSet the time you want the Unit to come on Set the time you want the Unit to turn offBefore Turning the Unit Off Setting the Sleep TimerTo Change the Sleep Timer Setting To Cancel the Sleep Timer SettingCare And Maintenance Action TroubleshootingSymptom Possible CauseDon’t service it yourself HOW to Locate Your JVC Service CenterLimited Warranty AUDIO-1 Specifications
Top Page Image Contents