JVC RX-E100RSL manual Basic Operations, Activating TV Direct, Press TV Direct

Activating TV Direct

TV Direct is enable you to use this unit as an AV selector while the unit is not turned on.

When TV Direct is activated, the pictures and sounds go from the video components such as DVD player to the TV through this unit. In this case, you can use the video components and the TV as if you connect them directly.

•This function takes effect only when the video components and TV are connected to this unit with SCART cables.

•This function takes effect to the following sources — DVD, STB, and VCR.

•This unit can be automatically turned on or off, and/or select the source automatically when you set the TV Direct mode to “AUTO 1” or “AUTO 2.” For details, see “Setting the TV Direct mode” on page 19.

To activate (or deactivate) TV Direct, follow the procedure below.

1 Press TV DIRECT. TV DIRECT

All the indications disappear, then the source indicator currently selected lights red.

2Turning on the video component and TV.

3Press one of the source selecting buttons — DVD,

STB, or VCR.

The indicator corresponding to the selected source lights red.

DVD STB VCR

To cancel TV Direct and turn off the unit, press (or

AUDIO on the remote control).

The unit is turned off and the STANDBY lamp lights up.

To cancel TV Direct and turn on the unit, press TV DIRECT on the unit (or AUDIO on the remote control).

The unit is turned on and the source indicator currently selected lights green.

Notes:

•When TV Direct is activated, you cannot enjoy all the sound effects this unit produces, and use the speakers connected to this unit.

•You can use T-V LINK function between TV and VCR while the TV Direct is activated.

Basic adjustment auto memory

This unit memorizes sound settings for each source ....

•when you turn on the power,

•when you change the source, and

•when you change the analogue/digital input mode (see page 14).

When you change the source, the memorized settings for the newly selected source are automatically recalled.

The following can be stored for each source:

•Analogue/digital input mode (see page 14)

•Input attenuator mode (see page 20)

•Balance (see page 20)

•Bass boost (see page 21)

•Tone adjustment (see page 21)

•Subwoofer output level (see page 22)

•Surround mode settings (see pages 33, 37) Theatre Surround settings (see pages 35, 38) DAP mode settings (see pages 36, 39)

Note:

If the source is FM or AM, you can assign a different setting for each band.

For recording

You can record sounds of any source playing through the unit to the VCR or the cassette deck.

While recording, you can listen to the selected sound source at whatever sound level you like without affecting the sound levels of the recording.

Note:

Sound adjustments (see page 20) and DSP modes (see page 32) cannot affect the recording.

Signal and speaker indicators on the display

Signal indicators								Speaker indicators
L	C	R	ANALOG	L	C	R	PRO LOGIC	SLEEP	L C	R
			LPCM				DSP
		LFE		SUBWFR LFE				SUBWFR
			DOLBY D	LS	S	RS	DGTL AUTO
			DTS				INPUT ATT
LS	S	RS
									LS	RS

The following signal indicators light up —:

L: • When digital input is selected: Lights up when the

left channel signal comes in.

•When analog input is selected: Always lights up.

R: • When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C : Lights up when the center channel signal comes in.

LS : Lights up when the left rear channel signal comes in.

RS : Lights up when the right rear channel signal comes in.

S : Lights up when the monaural rear channel signal comes in.

LFE: Lights up when the LFE channel signal comes in.

The speaker indicators light up as follows:

•The subwoofer speaker indicator (SUBWFR) lights up when “SUBWFR” is set to “YES” (see page 15).

•The other speaker indicators light up only when the corresponding speaker is activated AND when the corresponding speaker is required for the DSP mode currently selected.

Basic Operations

11