JVC RX-E100RSL manual Specifications, Per channel, min. RMS, Both channels

Page 49

Specifications

Designs & specifications are subject to change without notice.

Amplifier

Output Power

Audio

Audio Input Sensitivity/Impedance (1 kHz): Audio Input (DIGITAL IN)* :

Audio Output Level:

Signal-to-Noise Ratio (’66 IHF/DIN):

Frequency Response (8 Ω):

Tone Control:

Bass Boost:

Video

Video Input Sensitivity/Impedance (1 kHz): Composite video:

S-VIDEO:

RGB:

Video Output Level/Impedance (1 kHz): Composite video:

S-VIDEO:

RGB:

Signal-to-Noise Ratio (S/N):

Synchronize:

FM tuner (IHF)

Tuning Range:

Usable Sensitivity:

50 dB Quieting Sensitivity:

Signal-to-Noise Ratio (IHF-A weighted):

Total Harmonic Distortion:

Stereo Separation at REC OUT:

Alternate Channel Selectivity:

Frequency Response:

AM (MW/LW) tuner

Tuning Range:

Usable Sensitivity:

Signal-to-Noise Ratio:

General

Power Requirements:

Power Consumption:

Dimensions (W x H x D):

Mass:

At Stereo operation:

Front channels:

50 W per channel, min. RMS, Both channels

 

driven into 8 Ω at 1kHz with no more than 0.9%

 

total harmonic distortion. (IEC268-3/DIN)

At Surround operation:

 

Front channels:

50 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no

 

more than 0.8% total harmonic distortion.

Center channel:

50 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than

 

0.8% total harmonic distortion.

Rear channels:

50 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no

 

more than 0.8% total harmonic distortion.

DVD, STB, VCR, TV, TAPE:

180 mV/47 kΩ

Coaxial:

DIGITAL 1

(DVD):

0.5 Vp-p/75 Ω

Optical:

DIGITAL 2

(STB):

–21 dBm to –15 dBm (660 nm ±30 nm)

*Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).

VCR, TV, TAPE:

 

180 mV

 

DVD, STB, VCR, TV, TAPE:

85 dB/62 dB

DVD, STB, VCR, TV, TAPE:

20 Hz to 20 kHz (±1 dB)

Bass (100 Hz):

±10 dB

 

 

 

Treble (10 kHz):

±10 dB

 

 

 

+6 dB ± 1 dB at 70 Hz

 

 

 

 

DVD, STB, VCR, TV: 1 Vp-p/75 Ω

1 Vp-p/75 Ω

DVD, STB, VCR:

(Y:luminance):

 

(C:chrominance):

0.286 Vp-p/75 Ω

DVD, STB, VCR:

0.7 Vp-p/75 Ω

 

 

VCR, TV:

1 Vp-p/75 Ω

1 Vp-p/75 Ω

TV:

(Y:luminance):

 

(C:chrominance):

0.286 Vp-p/75 Ω

TV:

0.7 Vp-p/75 Ω

 

 

45 dB

 

 

 

 

Negative

 

 

 

 

87.50 MHz to 108.00 MHz

 

 

 

Monaural:

17.0 dBf (1.95 µV/75

Ω)

Monaural:

21.3 dBf (3.2 µV/75

 

Ω)

Stereo:

41.3 dBf (31.5 µV/75

Ω)

Monaural:

78 dB at 85 dBf

 

 

Stereo:

73 dB at 85 dBf

 

 

Monaural:

0.4% at 1 kHz

 

 

Stereo:

0.6% at 1 kHz

 

 

35 dB at 1 kHz

 

 

 

 

60 dB: (±400 kHz)

 

 

 

 

30 Hz to 15 kHz: (+0.5 dB, –3 dB)

 

 

MW:

522 kHz to 1 629 kHz

LW:

144 kHz to 288 kHz

 

Loop antenna

400 µV/m (MW)

 

 

 

50 dB (100 mV/m)

 

 

AC 230V , 50 Hz

110 W (at operation)

2 W (in standby mode)

17 3/16 in. x 3 15/16 in. x 15 11/16 in. (435 mm x 100 mm x 398 mm)

16.4 lbs (7.4 kg)

46

Image 49
Contents RX-E100RSL If in Doubt Consult a Competent Electrician RX-E100RSL Table of Contents Parts Identification Remote ControlFront Panel See pages in the parentheses for detailsChecking the Supplied Accessories Before Installation Putting Batteries in the Remote ControlGetting Started StartedGetting Started Connecting the FM and AM MW/LW AntennasFM Antenna supplied AntennaGetting Started Connecting the SpeakersRX-E100R Speaker Layout DiagramDigital connections Connecting Audio/Video ComponentsAnalogue connections Scart Terminal Specifications Plug the power cord into an AC outlet Connecting the Power CordTo turn off the power into standby Turn On the PowerBasic Operations TV DirectActivating TV Direct Basic OperationsPress TV Direct With the Timer Turning Off the PowerBasic Operations Basic Operations/Basic Settings Basic SettingsSetting the Digital Input Selecting the Analogue or Digital Input ModeBasic Settings Ex. When registering the rear speaker size Basic SettingsPress Control 3or 2 to select YES Press Control 3or 2 to select the appropriate speaker sizeDelay Time CTR DL, Rear DL Press Control 3 or 2 to select the delay timeDisplay TimeAppears on the display SETTINGThe Control buttons now work for basic settingsPress Control 3or 2 to select the crossover frequency level Crossover Frequency CrossPress Control 3 or 2 to select on or OFF Press Control 3or 2 to select the LFE attenuator levelLow Frequency Effect Attenuator LFE To cancel Auto Surround Setting the TV Direct modePress Control 3or 2 to select AUTO1 or, AUTO2 or Manual Repeat steps 1 and 2, then select OFF in stepPress Control 3 or 2to adjust the front Speaker balance Sound AdjustmentsPress Adjust AdjustReinforcing the Bass Adjusting the ToneAdjusting the Subwoofer Output Level Sound AdjustmentsPress Control 3 or 2to adjust the sound Output level AdjustmentsTuning in Stations Manually Sound Adjustments/Tuner OperationsTuner Operations Press FM/AM to select the bandTuner Operations Using Preset TuningPress Memory MemoryTo restore the stereo effect To tune in a preset stationPreset channel number appears Press Control 3or 2 to select MonoWhat information can RDS signals provide? Using the RDS Radio DataSearching for a Program Tuner OperationsBy PTY Codes Press PTY 9 or PTY untilJazz music Description of the PTY codesYour Choice Temporarily Switching to Broadcast ProgramCreating Realistic Sound Fields DAP Digital Acoustic Processor Modes Creating Realistic Sound FieldsCreating sound field HallDSP mode Surround modeWhen Auto SR Auto Surround is turned on Creating Realistic Sound FieldsWhen using the buttons on the front panel, see pages 37 to Using Surround Modes Remote ControlEx. When Dolby Digital is activated Press Test to check the speaker output balanceTo cancel Surround Mode Adjust the following speaker output levels from -10 to +10Press Test again to stop the test tone Press SoundPRO Logic and DSP indicator light up on the display To cancel Theatre Surround10 keys now work for sound adjustments Realistic Sound FieldsUsing DAP Modes Remote Control Adjust the rear speaker output levels from -10 to +10To cancel DAP Mode DSP indicator lights up on the displayPress Surround ON/OFF to activate an Using Surround Modes Front PanelDigital, or DTS Digital Surround SeePress Control 3or 2 to adjust the speaker output level Using Theatre Surround Front PanelRepeat steps 4 and 5 to adjust the other speaker levels Adjust DSP ModeRepeat steps 4 and 5 to make other adjustments Press Control 3or 2 to make an adjustmentUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Mastering Remote Operations Adjusting the sound and operating tuner KeysSelecting the channels and operating tuner Keys 10 0 +10Operating other JVC products Audio/video Mastering Remote OperationsOperation buttons Operating DVD menu for JVC DVD playerManufacturers’ codes for DVD player Try to operate your DVD player by pressingTry to operate your STB by pressing STB Manufacturers’ codes for STBManufacturers’ codes for VCR If there are more than one code listed for your brand of TVTry to operate your TV by pressing TV Manufacturers’ codes for TVMastering Remote Operations/Troubleshooting TroubleshootingProblem Possible Cause Solution Per channel, min. RMS, Both channels SpecificationsTotal harmonic distortion. IEC268-3/DIN 0301NHMMDWJEIN

RX-E100RSL specifications

The JVC RX-E100RSL is a standout receiver that perfectly blends modern technology with user-friendly features, making it an excellent choice for both casual listeners and serious audiophiles. This receiver is designed to provide high-quality sound performance without sacrificing ease of use.

One of the main features of the JVC RX-E100RSL is its robust power output, delivering 100 watts per channel. This substantial wattage ensures that it can drive a variety of speakers without compromising sound quality. Users will appreciate the clean and clear audio performance across all frequency ranges, whether they are engaging in a casual listening session or hosting a party with friends.

The RX-E100RSL is equipped with advanced digital signal processing technologies, enhancing the clarity and richness of audio. It supports various sound modes, enabling users to tailor their listening experience to suit different genres or personal preferences. The inclusion of built-in equalization options further allows for precise adjustments, contributing to optimal sound customization.

Another noteworthy characteristic of the RX-E100RSL is its connectivity options. The receiver features multiple inputs, including HDMI, optical, and analog connections, making it versatile for any home entertainment setup. Bluetooth connectivity is also integrated, allowing for wireless streaming from smartphones or tablets. This feature caters to the modern listener's preference for seamless audio streaming.

For video enthusiasts, the RX-E100RSL supports high-definition video pass-through, which means it can transmit video signals directly to your television while maintaining audio quality. It is designed to accommodate a wide range of devices, making it a suitable component in any home theater system.

In terms of build quality, the JVC RX-E100RSL boasts a sleek and stylish design, making it an attractive addition to any audio setup. The user interface is intuitive, with clear controls and a responsive display, simplifying the experience for users of all levels of expertise.

Overall, the JVC RX-E100RSL is an impressive receiver that combines advanced technology with practical features. Its powerful output, connectivity options, and customizable sound settings make it an ideal choice for anyone looking to enhance their audio experience at home. Whether you are watching movies, enjoying music, or playing video games, the RX-E100RSL delivers a satisfying audio performance that enriches your entertainment.