JVC RX-E100RSL manual Basic Settings, Press Control 3or 2 to select YES

Page 18

Setting the Subwoofer Information

Remote

NOT

When you have connected a subwoofer, follow the procedure below. If you do not use a subwoofer, you can skip this setting.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press SETTING.

SETTING

The CONTROL buttons now work for basic

 

settings.

2Press CONTROL °(or 5) repeatedly until “SUBWFR (Subwoofer)” (with the current

setting)* appears on the display.

CONTROL

GIC

 

UTO

 

TT

VOL

*“NO” is the initial setting. If you have already changed the setting, “YES” will be shown.

3Press CONTROL 3(or 2) to select “YES.”

• Each time you press the button, the subwoofer setting

alternates between “YES” and “NO.”

CONTROL

ANALOG

L

C

R

PRO LOGIC

 

LPCM

SUBWFR LFE DSP

 

DOLBY D

LS

S

RS

DGTL AUTO

VOL

DTS

INPUT ATT

1Press SETTING.

SETTING

The CONTROL buttons now work for basic

settings.

2Press CONTROL ° (or 5) repeatedly until one of the following speakers (with the current setting)* appears.

CONTROL

 

 

 

ANALOG

L

C

R

PRO LOGIC

 

LPCM

SUBWFR LFE

DSP

 

DOLBY D

LS

S

RS

DGTL AUTO

VOL

DTS

INPUT ATT

FR SP (Front Speaker)

: To register the front speaker size.

CTR SP (Center Speaker) : To register the center speaker size.

REAR SP (Rear Speaker) : To register the rear speaker size.

*“LRG (large)” is the initial setting for the front speakers, and “SML (small)” is for the center and rear speakers.

If you have already changed the setting, another size will be shown.

3Press CONTROL 3(or 2) to select the appropriate speaker size.

• Each time you press the button, the speaker size changes as

follows:

CONTROL

Basic Settings

YES : Select this when a subwoofer is used.

The subwoofer speaker indicator (SUBWFR) lights up on the display (see page 11). You can adjust the subwoofer output level (see page 22).

NO : Select this when you have not connected or have disconnected a subwoofer.

Setting the Speakers for

Remote

DSP Modes

NOT

To obtain the best possible surround effect from the DSP (Digital Signal Processor) modes (see page 32), register the following information after all connections are completed.

•Speaker Size — FR SP, CTR SP, REAR SP

•Delay Time — CTR DL, REAR DL

•Crossover Frequency — CROSS

•Dynamic Range Compression — D.R.C.

•Low Frequency Effect Attenuator — LFE

Speaker Size — FR SP, CTR SP, REAR SP

Register the sizes of all the connected speakers.

•When you change your speakers, register the information about the speakers again.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

ANALOG

L

C

R

PRO LOGIC

 

LPCM

SUBWFR LFE DSP

 

DOLBY D

LS

S

RS

DGTL AUTO

VOL

DTS

INPUT ATT

Ex.: When registering the rear speaker size

LRG (Large)

: Select this when the speaker size is relatively

 

large. (See “Notes” below.)

 

 

SML (Small)

: Select this when the speaker size is relatively

 

small. (See “Notes” below.)

 

 

NO

: Select this when you have not connected a

 

speaker. (Not selectable for the front speakers.)

 

 

4Repeat steps 2 and 3 to select the appropriate size for the other speakers.

Notes:

•Use the following criteria as reference when adjusting:

–If the size of the cone speaker unit built in your speaker is greater than 4 3/4 inches (12 cm ), select “LRG (large),” and if it is smaller than 4 3/4 inches (12 cm ), select “SML (small).”

•If you have selected “NO” for the subwoofer, you can only select “LRG (large)” for the front speaker size.

•If you have selected “SML (small)” for the front speaker size, you cannot select “LRG (large)” for the center and rear speaker sizes.

15

Page 17 Page 19
Image 18
Page 17 Page 19
Contents RX-E100RSL If in Doubt Consult a Competent Electrician RX-E100RSL Table of Contents Front Panel Remote ControlParts Identification See pages in the parentheses for detailsGetting Started Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories StartedFM Antenna supplied Connecting the FM and AM MW/LW AntennasGetting Started AntennaConnecting the Speakers Getting StartedSpeaker Layout Diagram RX-E100RConnecting Audio/Video Components Digital connectionsAnalogue connections Scart Terminal Specifications Connecting the Power Cord Plug the power cord into an AC outletBasic Operations Turn On the PowerTo turn off the power into standby TV DirectBasic Operations Activating TV DirectPress TV Direct Turning Off the Power With the TimerBasic Operations Setting the Digital Input Basic SettingsBasic Operations/Basic Settings Selecting the Analogue or Digital Input ModeBasic Settings Press Control 3or 2 to select YES Basic SettingsEx. When registering the rear speaker size Press Control 3or 2 to select the appropriate speaker sizeDisplay Press Control 3 or 2 to select the delay timeDelay Time CTR DL, Rear DL TimePress Control 3or 2 to select the crossover frequency level SETTINGThe Control buttons now work for basic settingsAppears on the display Crossover Frequency CrossPress Control 3or 2 to select the LFE attenuator level Press Control 3 or 2 to select on or OFFLow Frequency Effect Attenuator LFE Press Control 3or 2 to select AUTO1 or, AUTO2 or Manual Setting the TV Direct modeTo cancel Auto Surround Repeat steps 1 and 2, then select OFF in stepPress Adjust Sound AdjustmentsPress Control 3 or 2to adjust the front Speaker balance AdjustAdjusting the Tone Reinforcing the BassPress Control 3 or 2to adjust the sound Output level Sound AdjustmentsAdjusting the Subwoofer Output Level AdjustmentsTuner Operations Sound Adjustments/Tuner OperationsTuning in Stations Manually Press FM/AM to select the bandPress Memory Using Preset TuningTuner Operations MemoryPreset channel number appears To tune in a preset stationTo restore the stereo effect Press Control 3or 2 to select MonoUsing the RDS Radio Data What information can RDS signals provide?By PTY Codes Tuner OperationsSearching for a Program Press PTY 9 or PTY untilDescription of the PTY codes Jazz musicSwitching to Broadcast Program Your Choice TemporarilyCreating Realistic Sound Fields Creating sound field Creating Realistic Sound FieldsDAP Digital Acoustic Processor Modes HallWhen Auto SR Auto Surround is turned on Surround modeDSP mode Creating Realistic Sound FieldsEx. When Dolby Digital is activated Using Surround Modes Remote ControlWhen using the buttons on the front panel, see pages 37 to Press Test to check the speaker output balancePress Test again to stop the test tone Adjust the following speaker output levels from -10 to +10To cancel Surround Mode Press Sound10 keys now work for sound adjustments To cancel Theatre SurroundPRO Logic and DSP indicator light up on the display Realistic Sound FieldsTo cancel DAP Mode Adjust the rear speaker output levels from -10 to +10Using DAP Modes Remote Control DSP indicator lights up on the displayDigital, or DTS Digital Surround Using Surround Modes Front PanelPress Surround ON/OFF to activate an SeeRepeat steps 4 and 5 to adjust the other speaker levels Using Theatre Surround Front PanelPress Control 3or 2 to adjust the speaker output level Adjust DSP ModeUsing DAP Modes Front Panel Press Control 3or 2 to make an adjustmentRepeat steps 4 and 5 to make other adjustments Ex. When adjusting the left rear speaker output levelMastering Remote Operations Selecting the channels and operating tuner Keys Adjusting the sound and operating tuner KeysMastering Remote Operations 10 0 +10Operation buttons Mastering Remote OperationsOperating other JVC products Audio/video Operating DVD menu for JVC DVD playerTry to operate your STB by pressing STB Try to operate your DVD player by pressingManufacturers’ codes for DVD player Manufacturers’ codes for STBTry to operate your TV by pressing TV If there are more than one code listed for your brand of TVManufacturers’ codes for VCR Manufacturers’ codes for TVTroubleshooting Mastering Remote Operations/TroubleshootingProblem Possible Cause Solution Specifications Per channel, min. RMS, Both channelsTotal harmonic distortion. IEC268-3/DIN 0301NHMMDWJEIN

RX-E100RSL specifications

The JVC RX-E100RSL is a standout receiver that perfectly blends modern technology with user-friendly features, making it an excellent choice for both casual listeners and serious audiophiles. This receiver is designed to provide high-quality sound performance without sacrificing ease of use.

One of the main features of the JVC RX-E100RSL is its robust power output, delivering 100 watts per channel. This substantial wattage ensures that it can drive a variety of speakers without compromising sound quality. Users will appreciate the clean and clear audio performance across all frequency ranges, whether they are engaging in a casual listening session or hosting a party with friends.

The RX-E100RSL is equipped with advanced digital signal processing technologies, enhancing the clarity and richness of audio. It supports various sound modes, enabling users to tailor their listening experience to suit different genres or personal preferences. The inclusion of built-in equalization options further allows for precise adjustments, contributing to optimal sound customization.

Another noteworthy characteristic of the RX-E100RSL is its connectivity options. The receiver features multiple inputs, including HDMI, optical, and analog connections, making it versatile for any home entertainment setup. Bluetooth connectivity is also integrated, allowing for wireless streaming from smartphones or tablets. This feature caters to the modern listener's preference for seamless audio streaming.

For video enthusiasts, the RX-E100RSL supports high-definition video pass-through, which means it can transmit video signals directly to your television while maintaining audio quality. It is designed to accommodate a wide range of devices, making it a suitable component in any home theater system.

In terms of build quality, the JVC RX-E100RSL boasts a sleek and stylish design, making it an attractive addition to any audio setup. The user interface is intuitive, with clear controls and a responsive display, simplifying the experience for users of all levels of expertise.

Overall, the JVC RX-E100RSL is an impressive receiver that combines advanced technology with practical features. Its powerful output, connectivity options, and customizable sound settings make it an ideal choice for anyone looking to enhance their audio experience at home. Whether you are watching movies, enjoying music, or playing video games, the RX-E100RSL delivers a satisfying audio performance that enriches your entertainment.
Top Page Image Contents