JVC RX-E100RSL manual Getting Started, Connecting the Speakers

Page 8

AM (MW/LW) antenna connection

Connect the AM (MW/LW) loop antenna supplied to the AM LOOP terminals.

Turn the loop until you have the best reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. Keep the AM (MW/LW) loop antenna connected.

Connecting the Speakers

After connecting the front, center, rear speakers and/or a subwoofer, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 15.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the

speaker terminals.

Getting Started

FM antenna connection

Connect the FM antenna supplied to the FM 75 Ω COAXIAL terminal as temporary measure.

Extend the supplied FM antenna horizontally.

•If reception is poor, connect an outdoor antenna. Before attaching a 75 Ω coaxial cable (with a standard type

connector), disconnect the supplied FM antenna.

Notes:

• If the AM (MW/LW) loop antenna wire is covered with vinyl, remove the vinyl while twisting it as shown to the right.

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

Connecting the front, center, and rear speakers

1

2

3

 

 

 

For each speaker, connect the (+) and (–) terminals on the rear panel to the (+) and (–) terminals marked on the speakers respectively.

1Cut, twist and remove the insulation at the end of each speaker cord (not supplied).

2Open the terminal, then insert the speaker cord.

3Close the terminal.

Connecting the subwoofer speaker

By connecting a subwoofer, you can enhance the bass or reproduce the original LFE signals recorded in the digital software.

Powered subwoofer

 

(example)

 

INPUT

 

 

SUBWOOFER

HIGH IMPEDANCE

OUT

 

Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied).

•Refer also to the manual supplied for your subwoofer.

Since bass sound is non-directional, you can place a subwoofer wherever you like. Normally place it in front of you.

5

Page 7 Page 9
Image 8
Page 7 Page 9
Contents RX-E100RSL If in Doubt Consult a Competent Electrician RX-E100RSL Table of Contents Remote Control Parts IdentificationFront Panel See pages in the parentheses for detailsBefore Installation Putting Batteries in the Remote Control Checking the Supplied AccessoriesGetting Started StartedConnecting the FM and AM MW/LW Antennas Getting StartedFM Antenna supplied AntennaConnecting the Speakers Getting StartedSpeaker Layout Diagram RX-E100RAnalogue connections Connecting Audio/Video ComponentsDigital connections Scart Terminal Specifications Connecting the Power Cord Plug the power cord into an AC outletTurn On the Power To turn off the power into standbyBasic Operations TV DirectPress TV Direct Basic OperationsActivating TV Direct Basic Operations Turning Off the PowerWith the Timer Basic Settings Basic Operations/Basic SettingsSetting the Digital Input Selecting the Analogue or Digital Input ModeBasic Settings Basic Settings Ex. When registering the rear speaker sizePress Control 3or 2 to select YES Press Control 3or 2 to select the appropriate speaker sizePress Control 3 or 2 to select the delay time Delay Time CTR DL, Rear DLDisplay TimeSETTINGThe Control buttons now work for basic settings Appears on the displayPress Control 3or 2 to select the crossover frequency level Crossover Frequency CrossLow Frequency Effect Attenuator LFE Press Control 3or 2 to select the LFE attenuator levelPress Control 3 or 2 to select on or OFF Setting the TV Direct mode To cancel Auto SurroundPress Control 3or 2 to select AUTO1 or, AUTO2 or Manual Repeat steps 1 and 2, then select OFF in stepSound Adjustments Press Control 3 or 2to adjust the front Speaker balancePress Adjust AdjustAdjusting the Tone Reinforcing the BassSound Adjustments Adjusting the Subwoofer Output LevelPress Control 3 or 2to adjust the sound Output level AdjustmentsSound Adjustments/Tuner Operations Tuning in Stations ManuallyTuner Operations Press FM/AM to select the bandUsing Preset Tuning Tuner OperationsPress Memory MemoryTo tune in a preset station To restore the stereo effectPreset channel number appears Press Control 3or 2 to select MonoUsing the RDS Radio Data What information can RDS signals provide?Tuner Operations Searching for a ProgramBy PTY Codes Press PTY 9 or PTY untilDescription of the PTY codes Jazz musicSwitching to Broadcast Program Your Choice TemporarilyCreating Realistic Sound Fields Creating Realistic Sound Fields DAP Digital Acoustic Processor ModesCreating sound field HallSurround mode DSP modeWhen Auto SR Auto Surround is turned on Creating Realistic Sound FieldsUsing Surround Modes Remote Control When using the buttons on the front panel, see pages 37 toEx. When Dolby Digital is activated Press Test to check the speaker output balanceAdjust the following speaker output levels from -10 to +10 To cancel Surround ModePress Test again to stop the test tone Press SoundTo cancel Theatre Surround PRO Logic and DSP indicator light up on the display10 keys now work for sound adjustments Realistic Sound FieldsAdjust the rear speaker output levels from -10 to +10 Using DAP Modes Remote ControlTo cancel DAP Mode DSP indicator lights up on the displayUsing Surround Modes Front Panel Press Surround ON/OFF to activate anDigital, or DTS Digital Surround SeeUsing Theatre Surround Front Panel Press Control 3or 2 to adjust the speaker output levelRepeat steps 4 and 5 to adjust the other speaker levels Adjust DSP ModePress Control 3or 2 to make an adjustment Repeat steps 4 and 5 to make other adjustmentsUsing DAP Modes Front Panel Ex. When adjusting the left rear speaker output levelMastering Remote Operations Adjusting the sound and operating tuner Keys Mastering Remote OperationsSelecting the channels and operating tuner Keys 10 0 +10Mastering Remote Operations Operating other JVC products Audio/videoOperation buttons Operating DVD menu for JVC DVD playerTry to operate your DVD player by pressing Manufacturers’ codes for DVD playerTry to operate your STB by pressing STB Manufacturers’ codes for STBIf there are more than one code listed for your brand of TV Manufacturers’ codes for VCRTry to operate your TV by pressing TV Manufacturers’ codes for TVProblem Possible Cause Solution TroubleshootingMastering Remote Operations/Troubleshooting Total harmonic distortion. IEC268-3/DIN SpecificationsPer channel, min. RMS, Both channels 0301NHMMDWJEIN

RX-E100RSL specifications

The JVC RX-E100RSL is a standout receiver that perfectly blends modern technology with user-friendly features, making it an excellent choice for both casual listeners and serious audiophiles. This receiver is designed to provide high-quality sound performance without sacrificing ease of use.

One of the main features of the JVC RX-E100RSL is its robust power output, delivering 100 watts per channel. This substantial wattage ensures that it can drive a variety of speakers without compromising sound quality. Users will appreciate the clean and clear audio performance across all frequency ranges, whether they are engaging in a casual listening session or hosting a party with friends.

The RX-E100RSL is equipped with advanced digital signal processing technologies, enhancing the clarity and richness of audio. It supports various sound modes, enabling users to tailor their listening experience to suit different genres or personal preferences. The inclusion of built-in equalization options further allows for precise adjustments, contributing to optimal sound customization.

Another noteworthy characteristic of the RX-E100RSL is its connectivity options. The receiver features multiple inputs, including HDMI, optical, and analog connections, making it versatile for any home entertainment setup. Bluetooth connectivity is also integrated, allowing for wireless streaming from smartphones or tablets. This feature caters to the modern listener's preference for seamless audio streaming.

For video enthusiasts, the RX-E100RSL supports high-definition video pass-through, which means it can transmit video signals directly to your television while maintaining audio quality. It is designed to accommodate a wide range of devices, making it a suitable component in any home theater system.

In terms of build quality, the JVC RX-E100RSL boasts a sleek and stylish design, making it an attractive addition to any audio setup. The user interface is intuitive, with clear controls and a responsive display, simplifying the experience for users of all levels of expertise.

Overall, the JVC RX-E100RSL is an impressive receiver that combines advanced technology with practical features. Its powerful output, connectivity options, and customizable sound settings make it an ideal choice for anyone looking to enhance their audio experience at home. Whether you are watching movies, enjoying music, or playing video games, the RX-E100RSL delivers a satisfying audio performance that enriches your entertainment.
Top Page Image Contents