ProForm 985 user manual Inset drawing. The connectors should slide, Ful not to pinch the wires

Page 10

9. Slide the two Handrail Caps (80) onto the lower	9
ends of the Left Handrail (77) and the Right	9
Handrail (78) as shown.	5
Attach the Handrails (77, 78) to the Uprights (81,	5
83) with four 5/16" x 2 1/2" Patch Bolts (5), four	11
5/16" Star Washers (11), and two #8 x 3/4"	77		5
Screws (1). Firmly tighten the four 5/16" x 2 1/2"			5
Patch Bolts.			11
Orient the Handrail Caps (80) as shown. Slide	80	81	11
the Handrail Caps against the Uprights (81, 83).	80	81	83
		78	83
		78
		1	80
			80
			1

10. Have a second person hold the console assem-	10
bly near the Right Handrail (78). Connect the	10	Console
Wire Harness (84) to the console wire. See the		Console
inset drawing. The connectors should slide		Assembly
together easily and snap into place. If they do
not, turn one connector and try again. IF THE
CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN YOU TURN ON THE POWER.
Next, remove the wire tie from the Wire Harness.
Insert the connectors and the excess wire into				Console
the Right Handrail.		78	84	Console
Set the console assembly on the Right Handrail		78	84	Wire	Console
(78) and the Left Handrail (not shown). Be care-				Wire Tie	Console
ful not to pinch the wires.				Wire Tie	Wire
					84

10

Image 10

Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL16008.0 Serial No On the WEBTable of Contents Important Precautions Pulse sensors are not medical devicesPage Before YOU Begin Assembly Page Not fully fold the Frame yet Pinch the Wire Harness 84. Partially tightenBolts touch the Base do not fully tighten Patch Bolts yet Overtighten the Nut the Wheels must turn FreelyTouch the Base do not fully tighten the Patch Bolts yet Tighten the Bolts yetFul not to pinch the wires Inset drawing. The connectors should slideTogether easily and snap into place. If they do Be careful not to pinch the wires in the Right Handrail Raise the Frame 51 to the position shown HOW to PUT on the Chest Pulse Sensor HOW to USE the Chest Pulse SensorChest Pulse Sensor Care and Maintenance HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired HOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutHOW to USE the Stereo Sound System Information ModeHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem The chest pulse sensor does not function properly Turn if the walking belt has shifted to the rightWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFTL16008.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL16008.0 R0109A Exploded Drawing B-Model No. PFTL16008.0 R0109A Exploded Drawing C-Model No. PFTL16008.0 R0109A Exploded Drawing D-Model No. PFTL16008.0 R0109A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT