ProForm 985 user manual Raise the Frame 51 to the position shown

Page 12

14.Raise the Frame (51) to the position shown.

Have a second person hold the Frame until this step is completed.

Orient the Storage Latch (55) so that the large barrel and the Latch Knob (54) are in the posi- tions shown.

Remove the tie from the upper end of the Storage Latch (55). Attach the upper end of the Storage Latch to the bracket on the Frame (51) with a 3/8" x 2" Bolt (7) and a 3/8" Nut (13). Attach the Latch Bracket (95) to the bracket on the Base (90) with two 3/8" x 2" Bolts (7) and two 3/8" Nuts (13). Note: It may be necessary to move the Frame (51) back and forth to align the Latch Bracket with the bracket on the Base. Lower the Frame (51) (see HOW TO LOWER THE TREADMILL FOR USE on page 21).

14
	51
13		7
54		55
54
		Large
		Barrel
90	13	95	7

15.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is used to adjust the walking belt (see pages 23 and 24).

12

Image 12

Contents QUESTIONS? Model No. PFTL16008.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Pulse sensors are not medical devicesPage Before YOU Begin Assembly Page Pinch the Wire Harness 84. Partially tighten Bolts touch the Base do not fully tighten Patch Bolts yetNot fully fold the Frame yet Overtighten the Nut the Wheels must turn FreelyTouch the Base do not fully tighten the Patch Bolts yet Tighten the Bolts yetInset drawing. The connectors should slide Ful not to pinch the wiresTogether easily and snap into place. If they do Be careful not to pinch the wires in the Right Handrail Raise the Frame 51 to the position shown HOW to USE the Chest Pulse Sensor HOW to PUT on the Chest Pulse SensorChest Pulse Sensor Care and Maintenance Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleMeasure your heart rate if desired HOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode HOW to USE the Stereo Sound SystemHOW to Adjust the Cushioning System HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem The chest pulse sensor does not function properly Turn if the walking belt has shifted to the rightExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PFTL16008.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL16008.0 R0109A Exploded Drawing B-Model No. PFTL16008.0 R0109A Exploded Drawing C-Model No. PFTL16008.0 R0109A Exploded Drawing D-Model No. PFTL16008.0 R0109A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT