ProForm 985 user manual Turn if the walking belt has shifted to the right

Page 24

PROBLEM: The walking belt is off-center or slips when walked on

 

 

 

SOLUTION: a. If the walking belt is off-center, first remove the

a

 

 

key and UNPLUG THE POWER CORD. If the

 

 

walking belt has shifted to the left, use the hex

 

 

 

key to turn the left idler roller bolt clockwise 1/2 of a

 

 

 

turn; if the walking belt has shifted to the right,

 

 

 

turn the bolt counterclockwise 1/2 of a turn. Be

 

 

 

careful not to overtighten the walking belt. Then,

 

 

 

plug in the power cord, insert the key, and run the

 

 

 

treadmill for a few minutes. Repeat until the walk-

 

 

 

ing belt is centered.

 

 

 

b. If the walking belt slips when walked on, first re-

b

 

 

move the key and UNPLUG THE POWER CORD.

 

 

Using the hex key, turn both idler roller bolts clock-

 

 

 

wise, 1/4 of a turn. When the walking belt is cor-

 

 

 

rectly tightened, you should be able to lift each

 

 

 

edge of the walking belt 2 to 3 in. (5 to 7 cm) off

 

 

 

the walking platform. Be careful to keep the walk-

 

 

 

ing belt centered. Then, plug in the power cord, in-

 

 

 

sert the key, and carefully walk on the treadmill for

 

 

 

a few minutes. Repeat until the walking belt is

 

 

 

properly tightened.

 

 

 

PROBLEM: The chest pulse sensor does not function properly

 

 

 

SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROUBLE-

SHOOTING on page 13.

 

 

 

b. If the chest pulse sensor still does not function properly, the battery

b

Battery Cover

should be changed. To replace the battery, first locate the battery

cover on the back of the sensor unit. Insert a coin into the slot in the

 

 

cover, and turn the cover counterclockwise to the “open” position.

 

 

Then, remove the cover.

 

 

 

Next, remove the old battery from the sensor unit, and insert a new CR 2032 battery, with the battery oriented so the writing is on top. Make sure that the rubber gasket is in place in the sensor unit. Then, reinsert the battery cover and turn it to the closed position.

Battery

Cover

Battery

Rubber Gasket

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents QUESTIONS? Model No. PFTL16008.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Pulse sensors are not medical devicesPage Before YOU Begin Assembly Page Pinch the Wire Harness 84. Partially tighten Bolts touch the Base do not fully tighten Patch Bolts yetNot fully fold the Frame yet Overtighten the Nut the Wheels must turn FreelyTouch the Base do not fully tighten the Patch Bolts yet Tighten the Bolts yetInset drawing. The connectors should slide Ful not to pinch the wiresTogether easily and snap into place. If they do Be careful not to pinch the wires in the Right Handrail Raise the Frame 51 to the position shown HOW to USE the Chest Pulse Sensor HOW to PUT on the Chest Pulse SensorChest Pulse Sensor Care and Maintenance Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleMeasure your heart rate if desired HOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode HOW to USE the Stereo Sound SystemHOW to Adjust the Cushioning System HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem The chest pulse sensor does not function properly Turn if the walking belt has shifted to the rightExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PFTL16008.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL16008.0 R0109A Exploded Drawing B-Model No. PFTL16008.0 R0109A Exploded Drawing C-Model No. PFTL16008.0 R0109A Exploded Drawing D-Model No. PFTL16008.0 R0109A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents