ProForm 831.299510 user manual Trouble-Shooting, Symptom the Power does not Turn on, Top

Page 12

TROUBLE-SHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

1.SYMPTOM: THE POWER DOES NOT TURN ON

a.Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. Important: The treadmill is not compatible with GFCI-equipped outlets.

b.After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

2. SYMPTOM: THE POWER TURNS OFF DURING USE

c

Tripped

Reset

a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our toll-free HELPLINE.

3.SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY

a.Check the batteries in the console. See BATTERY INSTALLATION on page 8. Most problems are the result of drained batteries.

b. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two Resistance Bracket Bolts (78), Washers

(39)and Star Washers (29) from the left Upright (11). Remove the screws from the hood. Carefully remove the hood.

Locate the Reed Switch (44) and the Magnet (45) on the left side of the Pulley (50). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (33) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood first, then the left Upper Body Arm assembly. Run the treadmill for a few minutes to check for a cor- rect speed reading.

b

11

 

 

39

 

78

 

29

 

 

 

1/8”

50

 

44

 

 

 

 

45

 

33

 

 

Top

 

 

View

 

12

Image 12
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important PrecautionsPage Before YOU Begin Right SideBack Assembly Your own phillips screwdriver and wire cuttersPage Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Console Diagram Battery InstallationSTEP-BY-STEP Console Operation CALS/FAT Cals HOW to Fold and Move the Treadmill HOW to USE the Upper Body ArmsHOW to Fold the Treadmill for Storage HOW to Move the Treadmill HOW to Lower the Treadmill for USETROUBLE-SHOOTING Symptom the Power does not Turn onSymptom the Power Turns OFF During USE TopSymptom the Walking Belt Slows When Walked on Symptom the Walking Belt is OFF-CENTERSymptom ONE of the Upper Body Arms Squeaks During USE HOW to Measure Your Heart Rate Conditioning GuidelinesExercise Intensity Workout GuidelinesExercise Frequency Suggested StretchesRemove this Exploded Drawing and Part List from the Manual Part LIST-Model No Qty DescriptionExploded Drawing Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL