ProForm PFTL10909.0 R1009A warranty Troubleshooting, Compatible with GFCI-equipped outlets

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 14. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

Tripped

Reset

tripped. To reset the circuit breaker, wait for five

minutes and then press the switch back in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 22 to turn off the demo mode.

PROBLEM: The displays of the console do not function properly

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

THE POWER CORD. Place the treadmill in the

storage position (see HOW TO FOLD THE

 

TREADMILL FOR STORAGE on page 23).

 

Remove the two #8 x 1 1/2" Screws (111).

 

Then, lower the treadmill (see HOW TO LOWER

111

THE TREADMILL FOR USE on page 24).

 

111

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model No. PFTL10909.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Attach the other Wheel 95 in the same way Page Do not fully fold the Frame yet Not fully tighten the Patch Bolts yetTouch the Upright do not fully tighten Patch Bolts yet 2 Patch Bolt 4. Do not tighten the Patch Bolts yet To overtighten the ScrewsPatch Bolts used in this step. Slide Again. if the Connectors are not CON Patch Bolts yet. Be careful not to pinch Upright WireStart all six Patch Bolts before tightening any of them On page 17 and lower the incline to the low HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired. Before using Select a preset workout HOW to USE a Preset WorkoutStart the workout See on Select a competition workout HOW to USE a Competition WorkoutSee on HOW to USE the Stereo Sound System HOW to USE the Ifit Live Mode Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description Part LIST-Model No. PFTL10909.0Qty Exploded Drawing A-Model No. PFTL10909.0 R1009A Exploded Drawing B-Model No. PFTL10909.0 R1009A 107 Exploded Drawing D-Model No. PFTL10909.0 R1009A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents