ProForm PATL49708.0 user manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the dealer contact information on the back cover of this manual or on the included service card.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 14). If an exten-

sion cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft.

(1.5 m). IMPORTANT: The treadmill is not compatible with RCD-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes,

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 19 to turn off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

 

20

THE POWER CORD. Remove the three indicated

65

M4.2 x 19mm Hood Screws (20) and two M5.5 x

 

 

25mm Screws (25). Then, carefully remove the

 

 

 

Motor Hood (65).

 

25

 

 

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents QUESTIONS? Model No. PATL49708.0 Serial NoTable of Contents Important Precautions Tenance and adjustment procedures de Before YOU Begin Assembly Hold the Right Upright 54 so the two round Make sure that the power cord is unpluggedHoles are on top as shown. Attach the Right See the left inset drawing. Identify the two See the upper inset drawing. Locate the wireSee the lower inset drawing. Press the indi Outer side of the Frame Spacer facing Right UprightTop View Console Tie Wire Bracket Large Hole Nected PROPERLY, the Console MAY Again. if the Connectors are not CONBe Damaged When the Power is Turned on Then, firmly tighten all six BoltsPage Top View Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Start the walking beltMeasure your heart rate if desired Turn on the fan if desiredHOW to USE a Preset Workout Information Mode HOW to USE the Crosswalk ArmsHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The crosswalk arms squeak during use Problem The walking belt slows when walked onProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PATL49708.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PATL49708.0 R0809A R0809A Exploded Drawing C-Model No. PATL49708.0 Exploded Drawing D-Model No. PATL49708.0 Limited Warranty Ordering Replacement PartsIcon Authorized Dealer
Top Page Image Contents