ProForm DTL62950 user manual Enter your age, Enter a maximum speed setting

Page 14
Current Segment

4 Enter your age.

When a heart rate pro- gram is selected, the

word “AGE” will appear in the display and the current age setting will begin to flash. If you

have already entered your age, simply press the Start button (the program will not start at this time). If you have not entered your age, press the Set Pulse Rate buttons to enter your age, and then press the Start button.

5 Enter a maximum speed setting.

After you have entered your age, the letters

“SPd” will appear in the display and the maxi-

mum speed setting of the program will begin to

flash. If desired, press the Set Pulse Rate buttons to change the maximum speed setting, and then press the Start button (the program will not start at this time).

Press the Start button or the Speed + button to

6 start the program.

A moment after the button is pressed, the tread- mill will automatically adjust to the first speed and incline settings of the program. Hold the handrails and begin walking.

Each heart rate program is divided into 20 one- minute segments. One target heart rate is pro- grammed for each segment. Note: The same tar- get heart rate setting may be programmed for two or more consecutive segments.

The target heart rate

setting for the first seg-

ment will be shown in the

flashing

Current Segment column of the matrix. The target heart rate settings for the next four segments will be shown in the columns to the right.

When only three seconds remain in the first seg- ment of the program, both the Current Segment column and the column to the right will flash and a series of tones will sound. In addition, the speed setting and the incline setting will flash in the dis-

play to alert you. When the first segment ends, all target heart rate settings will move one column to the left. The target heart rate setting for the sec- ond segment will then be shown in the flashing Current Segment column.

During each segment, the console will compare your heart rate to the target heart rate. If your heart rate is too far below or above the target heart rate, the speed of the walking belt will auto- matically increase or decrease to bring your heart rate closer to the target heart rate. If the speed reaches the maximum speed setting of the pro- gram (see step 5 on this page) and your heart rate is still too far below the current target heart rate, the incline of the treadmill will also increase to bring your heart rate closer to the target heart rate.

The program will continue in this way until the tar- get heart rate setting for the last segment is shown in the Current Segment column and the last segment ends. The walking belt will then slow to a stop.

If the speed or incline setting is too high or too low at any time during the program, you can adjust the setting with the Speed or Incline buttons. However, each time the console compares your heart rate to the target heart rate, the speed and/or incline of the treadmill may automatically change to bring your heart rate closer to the target heart rate.

If your pulse is not detected during the program, the letters “PLS” will flash in the display and the speed and incline of the treadmill may automati- cally decrease. If this occurs, see the instructions included with the optional chest pulse sensor.

To stop the program at any time, press the Stop button. Heart rate programs cannot be stopped and then restarted. To use a heart rate program again, reselect the program and start it at the be- ginning.

7 Follow your progress with the display.

See step 5 on page 10.

8 Turn on the fan if desired.

See step 7 on page 11.

When you are finished exercising, remove the

9 key from the console.

See step 7 on page 13.

14

Image 14
Contents Customer HOT Line QUESTIONS?Model No. DTL62950 Serial No Table of Contents Important PrecautionsPage Back Before YOU BeginRight Side Assembly Make sure that the power cord is unpluggedUpright Base 107 Wire 116 Cylinder 108 PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeAvoid mov Measure your heart rate if desiredOn the foot Rails Turn on the fan if desiredHOW to USE a Preset Program Select one of the preset programsHOW to USE a Heart Rate Program Select a heart rate programEnter a maximum speed setting Enter your ageAudio Cable HOW to Connect Your MP3 Player or CD PlayerHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Press the Play button on your MP3 player, CD Player, or VCRMeasure your heart rate if desired Return to the treadmill and stand on the foot Directly from OUR WEB SiteFollow the on-line instructions to start Program Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Level the Treadmill HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R1104A Qty DescriptionQty Exploded DRAWING-Model No. DTL62950 108 109 111 101 103 100 112 107 104 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty