ProForm Not AvailablePFTL13810.0 Troubleshooting, Compatible with GFCI-equipped outlets

Page 21

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the problem that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

c

 

frame near the power cord. If the switch protrudes as

 

shown, the switch has tripped. To reset the switch,

Tripped

Reset

wait for five minutes and then press the switch back

in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 18 to turn off the demo mode.

PROBLEM: The displays of the console do not function properly

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

POWER CORD. Then, place the treadmill in the stor-

age position (see HOW TO FOLD THE TREADMILL

1

on page 20).

Next, remove the two indicated #8 x 3/4" Screws (1).

 

 

1

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model No. PFTL13810.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged To pinch the Upright WireTipping, or falling Wire 114. See the inset drawing. The con YOU Turn on the POWER. Next, removeNectors should slide together easily Wires are pinched Raise the Frame 67 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired. Before using HOW to USE a Performance Workout Select a performance workoutStart the workout Select a my memory workout HOW to Create a MY Memory WorkoutStart the walking belt HOW to USE a MY Memory WorkoutInformation Mode HOW to USE the Ifit Training ModeHOW to USE the Stereo Sound System HOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onKey and Unplug the Power CORD. Using Unplug the Power CORD. If the walking beltProblem The console display has lines running through it Walking belt has shifted to the right, turn the leftExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyQty Description Part LIST-Model No. PFTL13810.0Description Key No. Qty Exploded Drawing A-Model No. PFTL13810.0 R1010A Exploded Drawing B-Model No. PFTL13810.0 R1010A Exploded Drawing C-Model No. PFTL13810.0 R1010A Exploded Drawing D-Model No. PFTL13810.0 R1010A Exploded Drawing E-Model No. PFTL13810.0 R1010A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents