ProForm PCTL12009.0 user manual Be careful not to pinch the wires. Reattach

Page 12

14. Raise the Frame (51) to the position shown.

14

 

 

Have a second person hold the Frame until

 

 

this step is completed.

 

 

 

Orient the Storage Latch (55) so that the large

 

51

 

barrel and the Latch Knob (54) are in the posi-

 

 

tions shown.

13

 

 

Remove the tie from the upper end of the

 

7

Storage Latch (55). Attach the upper end of the

 

 

Storage Latch to the bracket on the Frame (51)

 

 

55

with a 3/8" x 2" Bolt (7) and a 3/8" Nut (13).

54

 

Attach the Latch Bracket (95) to the bracket on

 

 

the Base (90) with two 3/8" x 2" Bolts (7) and

 

 

Large

two 3/8" Nuts (13). Note: It may be necessary to

 

 

move the Frame (51) back and forth to align the

 

 

Barrel

Latch Bracket with the bracket on the Base.

90

 

Lower the Frame (51) (see HOW TO LOWER

13

95 7

THE TREADMILL FOR USE on page 21).

 

15.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is used to adjust the walking belt (see pages 23 and 24).

If you purchase the optional chest pulse sensor (see page 19), follow the steps below to install the re- ceiver included with the chest pulse sensor.

1.Make sure that the power cord is unplugged. Remove the indicated #8 x 3/4" Screw (1) and the Access Door (104) from the Console Base (98).

2. Connect the wire on the receiver to the indicated

 

 

 

wire extending from the Console Base (98).

 

 

 

Hold the receiver so the antenna is oriented

 

 

 

as shown and is facing the Console Base.

98

Small Screws

Wires

Attach the receiver to the plastic posts on the

Access Door (104) with the included small

 

Receiver

 

screws.

 

Antenna

 

3. Be careful not to pinch the wires. Reattach

 

104

 

 

the Access Door (104) with the #8 x 3/4" Screw

 

 

(1). Discard the other wires included with the re-

 

1

 

ceiver.

 

 

12

Image 12
Contents QUESTIONS? Model No. PCTL12009.0 Serial NoContact OUR Customer SER- Vice Department Directly Table of Contents Important Precautions Various factors, including the users movePage Before YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yetOvertighten the Nut the Wheels must turn Freely Pinch the Wire Harness 84. Partially tighten Bolts touch the Base do not fully tighten Patch Bolts yetNot fully fold the Frame yet Touch the Base do not fully tighten the Patch Bolts yet Bolts 3 do not tighten the Bolts yetInset drawing. The connectors should slide Ful not to pinch the wiresFirmly tighten the four 5/16 x 2 1/2 Patch Bolts Together easily and snap into place. If they doBe careful not to pinch the wires in the Right Handrail Be careful not to pinch the wires. Reattach Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleTurn on the fan if desired HOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on Problem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PCTL12009.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PCTL12009.0 R0110A Exploded Drawing B-Model No. PCTL12009.0 R0110A Exploded Drawing C-Model No. PCTL12009.0 R0110A Exploded Drawing D-Model No. PCTL12009.0 R0110A Ordering Replacement Parts Limited Warranty