ProForm PCTL12009.0 user manual Problem The walking belt slows when walked on

Page 23
1/8 in. 17 69
Top
View
48
50

Remove the three #8 x 3/4" Screws (1) and care-

 

 

fully pivot the Motor Hood (62) off.

1

1

62

Locate the Reed Switch (69) and the Magnet (48) on the left side of the Pulley (50). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If nec- essary, loosen the #8 x 3/4" Clamp Screw (17), move the Reed Switch slightly, and then retighten

the Screw.

Reattach the Hood (not shown). Reattach the #8 x

2" Screws (not shown) if necessary. Run the tread- mill for a few minutes to check for a correct speed reading.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.

b. If the walking belt is overtightened, treadmill perfor-

b

 

mance may decrease and the walking belt may be-

2–3 in.

come damaged. Remove the key and UNPLUG

 

THE POWER CORD. Using the hex key, turn both

 

 

idler roller bolts counterclockwise, 1/4 of a turn.

 

 

When the walking belt is properly tightened, you

 

 

should be able to lift each edge of the walking belt

 

 

2 to 3 in. (5 to 7 cm) off the walking platform. Be

 

 

careful to keep the walking belt centered. Then,

 

 

plug in the power cord, insert the key, and run the

Idler Roller Bolts

treadmill for a few minutes. Repeat until the walk-

ing belt is properly tightened.

 

 

c. If the walking belt still slows when walked on, see the front cover of this manual.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Contact OUR Customer SER- Vice Department Directly QUESTIONS?Model No. PCTL12009.0 Serial No Table of Contents Various factors, including the users move Important PrecautionsPage Before YOU Begin Assembly Overtighten the Nut the Wheels must turn Freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet Not fully fold the Frame yet Pinch the Wire Harness 84. Partially tightenBolts touch the Base do not fully tighten Patch Bolts yet Bolts 3 do not tighten the Bolts yet Touch the Base do not fully tighten the Patch Bolts yetTogether easily and snap into place. If they do Inset drawing. The connectors should slideFul not to pinch the wires Firmly tighten the four 5/16 x 2 1/2 Patch BoltsBe careful not to pinch the wires in the Right Handrail Be careful not to pinch the wires. Reattach PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeTurn on the fan if desired Select one of the preset workouts. To select one HOW to USE a Preset WorkoutInsert an iFit card and select a workout HOW to USE AN Ifit WorkoutOptional Chest Pulse Sensor Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Problem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. PCTL12009.0Qty Exploded Drawing A-Model No. PCTL12009.0 R0110A Exploded Drawing B-Model No. PCTL12009.0 R0110A Exploded Drawing C-Model No. PCTL12009.0 R0110A Exploded Drawing D-Model No. PCTL12009.0 R0110A Limited Warranty Ordering Replacement Parts
Top Page Image Contents