ProForm 760 user manual Problem The walking belt slows when walked on

Page 26

Remove the three #8 x 3/4" Screws (12) and care- fully pivot the Hood (61) off.

12

61

Locate the Reed Switch (71) and the Magnet (50) on the left side of the Pulley (51). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the #8 x 3/4" Switch Screw (15), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown). If neces- sary, tip down the Uprights (not shown), reattach the #8 x 2" Screws (not shown), and raise the Uprights. Run the treadmill for a few minutes to check for a correct speed reading.

1/8 in.

15

50

71

51

Top

View

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. Hold down the Stop button and the Speed increase button, insert the key into the console, and then release the Stop button and the Speed increase button. Press the Incline increase or de- crease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system. If the incline does not calibrate, press the Stop button, and then press the Incline increase or decrease button again. When the incline is calibrated, remove the key from the console.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2–3 in.

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the front cover of this manual.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL79707.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Hardware may be includedTighten the Nut the Wheel must turn freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet See the inset drawing. Tie the long tieBe careful not to pinch the Upright Wire Not fully tighten the Bolts yetFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleChange the incline of the treadmill as desired Measure your heart rate if desired Turn on the fan if desiredPress the Quick Start button to start the work- out HOW to USE a Cross Training WorkoutSelect a cross training workout Continue the cross trainer workout HOW to USE a Classic Aerobic Workout Select a classic aerobic workoutStart the workout Select the monthly challengeGet a monthly challenge goal Complete the workout. See steps 4-9 onHOW to Review Your Monthly Challenge LOG Information ModeOptional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0408A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL79707.0 R0408A Exploded Drawing B-Model No. PFTL79707.0 R0408A Exploded Drawing C-Model No. PFTL79707.0 R0408A Exploded Drawing D-Model No. PFTL79707.0 R0408A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents