ProForm 760 user manual Assembly, Hardware may be included

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own Phillips screwdriver

,

adjustable wrench

, rubber mallet

, and scissors

.

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra

hardware may be included.

3/8" Star

#10 Star

 

 

Washer (10)–2

3/8" Nut (8)–5

Washer (9)–8

 

 

 

Base Pad

 

 

 

 

 

 

Spacer (13)–2

 

 

#8 x 1/2"

#8 x 1/2" Washer Head

Bolt Spacer (80)–4

Screw (1)–2

Screw (16)–4

#8 x 3/4"

#8 x 3/4" Handrail

#10 x 3/4"

#8 x 1" Tek Screw (2)–4

Screw (12)–4

Screw (15)–2

Screw (5)–2

 

3/8" x 1 1/4" Bolt (7)–4

3/8" x 2" Shoulder Bolt (111)–2

3/8" x 2" Bolt (4)–3

 

3/8" x 4 1/2" Bolt (6)–4

 

 

 

6

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents QUESTIONS? Model No. PFTL79707.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Hardware may be includedTighten the Nut the Wheel must turn freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet See the inset drawing. Tie the long tieBe careful not to pinch the Upright Wire Not fully tighten the Bolts yetFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleChange the incline of the treadmill as desired Measure your heart rate if desired Turn on the fan if desiredHOW to USE a Cross Training Workout Select a cross training workoutPress the Quick Start button to start the work- out Continue the cross trainer workout HOW to USE a Classic Aerobic Workout Select a classic aerobic workoutStart the workout Select the monthly challengeGet a monthly challenge goal Complete the workout. See steps 4-9 onHOW to Review Your Monthly Challenge LOG Information ModeOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0408A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL79707.0 R0408A Exploded Drawing B-Model No. PFTL79707.0 R0408A Exploded Drawing C-Model No. PFTL79707.0 R0408A Exploded Drawing D-Model No. PFTL79707.0 R0408A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents