7.Identify the Left Handlebar (9), which is marked with a sticker. Insert the Left Handlebar into one of the Handlebar Legs (79); make sure that the Handlebar
Leg is turned so the hexagonal holes are on the indicated side. Attach the Left Handlebar with two M8 x 43mm Button Bolts (50) and two M8 Nylon Locknuts (46). Do not tighten the Button Bolts yet. Make sure that the Nylon Locknuts are seated in the hexagonal holes.
Attach the Right Handlebar (not shown) to the other Handlebar Leg (not shown) in the same way.
8.Apply a generous amount of grease to the Pivot Axle (108) and to the two M8.5 Small Washers (53). Insert the Pivot Axle into the Upright (2) and center it. Reapply grease to both sides of the Pivot Axle.
Identify the Left and Right Handlebars (9, 10), which are marked with stickers. Slide a Handlebar Spacer
(25)onto the short tube on each Handlebar, and slide the Handlebars onto the Pivot Axle (108). Make sure that the Handlebars are on the correct sides.
Orient the two Handlebar Caps (23) as shown, and press the small tabs on the Handlebar Caps into the two Handlebar Spacers (25). Tighten an M8 x 19mm Shoulder Screw (22) with an M8.5 Small Washer (53) into each end of the Pivot Axle (108).
9.Remove the Chrome Tube (118) from the left Handlebar Leg (79). Apply a small amount of the included Teflon® lubricant to a paper towel, and rub a thin film of lubricant onto the Chrome Tube. Then, rein- sert the Chrome Tube into the Handlebar Leg.
See the drawing at the right and the inset drawing. Apply a thin film of grease to the shaft of a Union Bolt Set (27). Insert the shaft of the Union Bolt Set into the side of the left Flex Bar (14) closest to the Upright (2), and then slide a 4.7mm Spacer (143) onto the shaft. Next, slide the end of the left Chrome Tube (118) onto the shaft and onto the Spacer. Then, slide a Wheel Bushing (28), a Ramp Wheel (119), and another Wheel Bushing onto the shaft. Make sure that all parts are oriented exactly as shown. Insert the shaft completely through the Flex Bar and tighten the screw of the Union Bolt Set into the shaft.
Repeat this step to attach the right Chrome Tube (118) to the right Flex Bar (14).
8
7 |
|
|
|
|
|
|
| 9 |
|
|
|
|
|
| 46 |
|
|
|
| 50 | Hexagonal | ||
|
|
| |||
|
|
| Holes |
| |
|
| 79 |
|
| |
8 |
|
|
|
|
|
|
|
| 10 |
| 22 |
|
|
|
| 53 | |
|
|
|
| 23 | |
| 9 |
| Tube |
|
|
|
|
|
| Grease | |
| Tube | 108 | |||
|
|
|
| ||
53 | 23 |
| 25 |
|
|
22 |
| 25 |
|
|
|
|
|
|
|
| |
Grease | 2 |
|
|
| |
|
|
|
|
| |
9 |
| 79 |
|
|
|
|
|
|
|
| |
|
|
| 2 |
|
|
| Lubricate |
| 118 | ||
|
| 118 | 143 |
|
|
| 119 | 28 |
|
| 14 |
|
| 27 |
| ||
|
|
|
| ||
|
|
|
|
| |
| 28 |
|
|
|
|
|
| 27 | 14 |
|
|
|
| 119 | 118 | Grease | |
27 | 14 | 143 14 | |||
|
|
|
|
| 27 |
Screw | 28 | 28 | Shaft |
| |
|
|
|
| ||