ProForm PFCCEL45011 user manual Ing the wire harnesses, Handlebar Legs, Two M8 Nylon Locknuts

Page 7

6.While another person holds the Console (23) in the position shown, connect the wire harness on the Console to the Extension Wire Harness (44). Insert the excess wire harness into the Upright Extension (73).

Attach the Console (23) to the Upright Extension (73) with three M10 x 27mm Button Screws (67) and three M10 Split Washers (59). Be careful to avoid pinch-

ing the wire harnesses.

Snap the bookrack onto the Console (23) in the indicat- ed location.

7.Identify the Left Handlebar (6), which is marked with a sticker. Insert the Left Handlebar into one of the

Handlebar Legs (5);

make sure that the Handlebar

Leg is turned so the hexagonal holes are on the

 

indicated side

. Attach the Left Handlebar to the

Handlebar Leg with two M8 x 45mm Button Bolts (50)

and two M8 Nylon Locknuts (38).

Make sure that the

Nylon Locknuts are inside of the hexagonal holes.

 

Do not fully tighten the Button Bolts yet.

 

Apply a small amount of the included grease to the left and right axles on the Upright (2).

Make sure that there are two Small Handlebar

Bushings (49) in the Left Handlebar (6). C arefully slide an Upright Spacer (48), a Handlebar Spacer (47), the

Left Handlebar, and a Handlebar Cap (46) onto the left axle on the Upright (2) as shown. Slide a Handlebar Washer (55) onto an M8 x 19mm Button Screw (56), and tighten the Button Screw into the axle.

Assemble the Right Handlebar (8) and the other

Handlebar Leg (5) in the same way.

8.Identify the left Pedal Spring (11), which is marked with a sticker. Attach the Left Pedal (13) to the left Pedal Spring with an M10 x 27mm Pedal Bolt (80), an M10 Washer (78), and a Pedal Knob (81) as shown. Note: The Left Pedal can be attached in any of five positions (see HOW TO ADJUST THE PEDALS AND THE

UPRIGHT on page 9).

Attach the Right Pedal (not shown) in the same way. Make sure that both Pedals are in the same position.

7

6

 

Bookrack

 

 

 

 

 

23

 

 

 

 

Wire Harness

 

 

67

44

 

 

59

67

 

 

59

 

 

 

 

 

67

73

 

 

 

 

7

 

 

 

 

Grease

 

8

 

6

 

 

55

46

48

2

47

 

 

 

 

 

 

 

49

 

 

56

38

 

 

5

 

 

 

 

 

 

50

 

 

 

Hexagonal

 

 

 

Holes

 

 

 

5

 

 

8

80

 

 

 

 

 

 

13

 

 

 

11

 

 

 

78

 

 

 

81

 

 

Image 7
Contents Model No. PFCCEL45011 Serial No QUESTIONS?Serial Number Decal Table of Contents Always hold the handgrip pulse sensor or Important PrecautionsLeft Side Before YOU BeginYou use the Proform FrontWrench A rubber mallet AssemblyWire harnesses To the Wire HarnessExtension Wire Harness Frame Do not pinch the Wire HarnessesHandlebar Legs Ing the wire harnessesTwo M8 Nylon Locknuts Installing the Receiver for the Optional Chest Pulse Sensor Pedal disks Can turn HOW to USE the Elliptical CrosstrainerHOW to Adjust the Pedals and the Upright PinFeatures of the Console Surement Will change from one mode to the nextConsole Description Tinuous displayHOW to USE the Manual Mode Select one of the six Smart programs HOW to USE a Smart ProgramFollow your progress with the feedback modes Start the program HOW to USE a Heart Rate ProgramSelect one of the two Heart Rate programs Enter your ageTo use HOW to Connect Your CD PLAYER, VCR Or ComputerHOW to Connect Your Portable CD Player Followmodes. your progress with the feedbackAudio Cable HOW to Connect Your Portable StereoHOW to Connect Your Home Stereo Audio CableJack on your VCR HOW to Connect Your VCRAudio Cable Wire removed from Audio OUT jack Audio Cable AdapterCD PLAYER, VCR, or Computer on ProgramsPressVCR. the play button on your CD player or HOW to USE Programs Directly from OUR WEB Site From the Left Side Shield 3 and remove the Left Side Shield Battery ReplacementHandgrip Pulse Sensor TROUBLE-SHOOTING HOW to Adjust the Reed SwitchExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesDescription R0702A6828 R0702ALimited Warranty HOW to Order Replacement PartsPart No R0702A