NordicTrack NTL15008.5 user manual Troubleshooting, Important The incline trainer

Page 21

TROUBLESHOOTING

Most incline trainer problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 12.

IMPORTANT: The incline trainer

is not compatible with GFCI-equipped outlets.

 

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the in-

c

 

 

cline trainer frame near the power cord. If the switch

 

 

protrudes as shown, the circuit breaker has tripped.

 

Tripped

Reset

To reset the circuit breaker, wait for five minutes and

 

then press the switch to the reset position.

 

 

 

PROBLEM: The power turns off during use

 

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the incline trainer still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the incline trainer is displayed

in a store. If the displays remain lit when you remove the key and the incline rises to the maxi-

mum level, the demo mode is turned on. To turn off the demo mode, hold down the Stop button

for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 19 to turn

off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

POWER CORD. Next, remove the three indicated #8

 

x 1/2" Screws (12). Lift off the Left Roller Cover (35).

 

35

 

 

 

12

12

21

Image 21
Contents Model No. NTL15008.5 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly See the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedEning any of them. Be careful not to pinch Upright Wire Overtighten the Tek ScrewsNot to pinch the Left Pulse Wire Bolts Washers 25 do not fully tighten the Bolts YetSert all of the tabs. Make sure not to break Tabs Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to USE the Manual Mode Turn on the fan if desired Measure your heart rate if desiredStart the walking belt HOW to USE a 1 Step Calorie WorkoutHOW to USE a Random Workout HOW to USE AN Ifit Card HOW to USE the Stereo Sound System Information ModeHOW to Move the Incline Trainer Problem The power turns off during use TroubleshootingImportant The incline trainer Is not compatible with GFCI-equipped outletsTop Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description R0310AKey No. Qty Description Exploded Drawing A-Model No. NTL15008.5 Exploded Drawing B-Model No. NTL15008.5 Exploded Drawing C-Model No. NTL15008.5 Exploded Drawing D-Model No. NTL15008.5 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT