NordicTrack NTL15008.5 user manual Measure your heart rate if desired, Turn on the fan if desired

Page 15

5.Monitor your progress with the display. When the manual mode is selected, the console offers four display modes. The display mode that you select will determine which workout informa- tion is shown. Press the Display Mode button re- peatedly to select the desired display mode.

As you walk or run on the incline trainer, the dis- play can show the following workout information:

The elapsed time.

The distance that you have walked or run.

The number of vertical feet you have climbed.

The approximate number of calories burned per hour.

The speed of the walking belt.

The incline level of the incline trainer.

The approximate number of calories you have burned.

Your heart rate. Note: Your heart rate can be displayed only while you use the handgrip pulse sensor (see step 6).

Regardless of which display mode you select, the speed or incline setting will appear in the display for a few seconds each time you change the setting.

If desired, adjust the volume by pressing the Volume (VOL) increase and decrease buttons on the console.

To reset the console, press the Stop button, re- move the key, and then reinsert the key.

6.Measure your heart rate if desired.

Before using the handgrip pulse sensor, remove the sheets of plastic from the metal contacts if nec- essary. In addition, make sure that your hands are clean.

To measure your heart

rate, stand on Contacts the walking

platform and hold the metal contacts on the handrail— avoid moving your hands.

Hold the contacts for approximately ten seconds. When your pulse is detected, your heart rate will be shown. For the most accurate heart rate reading, continue to hold the contacts for about 15 seconds.

7.Turn on the fan if desired.

The fan has high and low speed settings. Press the Fan button repeatedly to select a fan speed or to turn off the fan. Note: If the fan is on when the walking belt stops, the fan will automatically turn off after a few minutes.

8.When you are finished exercising, remove the key from the console.

Step onto the walking platform and press the Stop button. If the console is in demo mode (see THE INFORMATION MODE on page 19), the incline will automatically rise to the maximum incline level. Next, remove the key from the console and put it in a secure place.

When you are finished using the incline trainer, switch the reset/off circuit breaker to the “off” posi- tion and unplug the power cord. IMPORTANT: If you do not do this, the incline trainerʼs electri- cal components may wear prematurely.

15

Image 15
Contents On the WEB QUESTIONS?Model No. NTL15008.5 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Page Before YOU Begin Assembly Overtighten the Tek Screws Make sure that the power cord is unpluggedSee the inset drawing. Tie the wire tie Ening any of them. Be careful not to pinch Upright WireNot to pinch the Left Pulse Wire Bolts Washers 25 do not fully tighten the Bolts YetSert all of the tabs. Make sure not to break Tabs Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to USE the Manual Mode Turn on the fan if desired Measure your heart rate if desiredStart the walking belt HOW to USE a 1 Step Calorie WorkoutHOW to USE a Random Workout HOW to USE AN Ifit Card HOW to USE the Stereo Sound System Information ModeHOW to Move the Incline Trainer Is not compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Important The incline trainerTop Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description R0310AKey No. Qty Description Exploded Drawing A-Model No. NTL15008.5 Exploded Drawing B-Model No. NTL15008.5 Exploded Drawing C-Model No. NTL15008.5 Exploded Drawing D-Model No. NTL15008.5 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT