JVC MX-J300 Listening to FM and AM Broadcasts, Tuning in a Station, Tuning in a Preset Station

Page 17
FM /AM
FM /AM

Listening to FM and AM Broadcasts

Tuning in a Station

On the unit ONLY:

1 Press FM/AM.

The unit automatically turns on and tunes in the previously tuned station (either FM or AM). (For MX-J300 only, the Powered Rolling Panel automatically opens.)

Each time you press the button, the band alternates between FM and AM.

2

Press and hold TUNING – / + for

TUNING +

 

 

 

more than 1 second.

 

 

 

 

 

The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in.

2 Press SET.

BASS

SOUND MODE

REC

3 Press PRESET – / + to select a preset number.

4 Press SET again.

BASS

SOUND MODE

REC

SET

PRESET +

SET

If a program is broadcast in stereo, the ST (stereo) indicator lights up.

To stop during searching, press TUNING – / +.

When you press TUNING – / + briefly and repeatedly

The frequency changes step by step.

To change the FM reception mode

 

When an FM stereo broadcast is hard to receive or

FM MODE

noisy, press FM MODE on the remote control so

 

that the MONO indicator lights up on the display.

 

Reception improves.

 

To restore the stereo effect, press FM MODE again so that the MONO indicator goes off.

In this stereo mode, you can hear stereo sounds when a program is broadcast in stereo.

The tuned station in step 1 is stored in the preset number selected in step 3.

Storing a new station on a used number erases the previously stored one.

When you unplug the AC power cord or if a power failure occurs

The preset stations will be erased in a few days. If this happens, preset the stations again.

Tuning in a Preset Station

1 Press FM/AM.

The unit automatically turns on and tunes in the previously tuned station (either FM or AM.) (For MX-J300 only, the Powered Rolling Panel automatically opens.)

Each time you press the button, the band alternates between FM and AM.

Presetting Stations

You can preset 30 FM and 15 AM stations.

In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1 Tune in the station you want to preset.

• See “Tuning in a Station” above.

MHz

2 Select a preset number. On the unit:

Press PRESET – / +. On the remote control: Press the number buttons.

For preset number 5, press 5. For preset number 15, press +10

then 5.

For preset number 20, press +10, then 10.

For preset number 25, press +10, +10, then 5.

PRESET +

1 2 3

4 5 6

7 8 9

10 +10

– 14 –

Image 17
Contents MX-J300 MX-J200 Mises en garde, précautions et indications diverses For Canada/pour le Canada About This Manual PrecautionsIntroduction Contents CA-MXJ300 Location of the Buttons and ControlsDisplay Window Powered Rolling PanelCA-MXJ300 Front Panel CA-MXJ200 These buttons do not function as 1 / Á CA-MXJ200 Front PanelRemote Control Remote ControlGetting Started Connecting AntennasUnpacking FM antennaRelease the finger from the clamp Connecting SpeakersAM antenna To connect an outdoor AM antennaPress and hold Demo for more than Seconds.DEMO Connecting Other EquipmentTo connect audio equipment To start the display demonstration manuallyCommon Operations Setting the ClockAdjusting the Volume Turning On the Power and Selecting the SourcesSelecting the Sound Modes Reinforcing the Bass SoundTo select the sound modes, press Sound Surround modesTuning in a Preset Station Tuning in a StationPresetting Stations Listening to FM and AM BroadcastsLoading CDs Playing Back CDsPlaying Back the Entire Discs Continuous Play Basic CD OperationsProgram Play To check the program contents Select the Random play mode On the unitPlaying at Random Random Play Prepare CDsIf you try to eject CDs Repeating Tracks or CDs Repeat PlayProhibiting Disc Ejection Tray Lock Playing Back a Tape Playing Back TapesRecording Tapes on Deck B RecordingPress Eject 0for the deck B Start recording On the unit Press REC START/STOPDubbing Tapes To record on both sides Reverse ModeCD Direct Recording Press DubbingUsing Daily Timer Using the TimersWhen selecting Tuner FM or Tuner AM When selecting CDPress 4or ¢to set the volume level Press TimerSet the volume level Using Recording TimerTimer setting How Recording Timer actually worksPress Timer until REC appears To turn on On the remote controlPress Power to turn off the unit on standby if necessary Put a recordable cassette into deck B Press ShiftUsing Sleep Timer Timer PrioritySelect the preset station On the remote control only Press SleepCassette decks MaintenanceHandling discs Specifications TroubleshootingHOW to Locate Your JVC Service Center Limited Warranty AUDIO-1 0200KSMMDWHIT