JVC MX-J300 manual Using Recording Timer, Press Select or Select + to, Set the volume level

Page 27

Continued

6 Press SELECT – or SELECT + to select the source to play, then press SET.

•Each time you press SELECT + or SELECT –, the source changes as follows:

TUNER FM TUNER AM

AUX TAPE – CD – – –

– SELECT +

4

5

SET

8

Using Recording Timer

With Recording Timer, you can make a tape of a radio broadcast automatically.

How Recording Timer actually works

The unit automatically turns on, tunes into the specified station, sets the volume level to “MIN,” and starts recording

when the on-time comes (the indicator flashes just before the on-time, and continues flashing while the timer is

TUNER FM: tunes into a specified preset FM station.

=go to step 7.

TUNER AM: tunes into a specified preset AM station.

=go to step 7.

–CD – – –: plays a disc from a specified track of a specified disc. =go to step 7.

• Make sure there is a CD on the selected disc number tray.

TAPE: plays a tape in deck A or B. =go to step 8.

•Make sure that a tape is in the deck whose deck indicator (A or B) is lit on the display.

•Make sure that the tape direction is correct. AUX: plays an external source.=go to step 8.

•To use this setting, the external component has to be equipped with the timer function.

operating). Then, when the off-time comes (“OFF” appears just before the off-time), the unit automatically turns off (stands by).

The timer setting remains in memory until you change it.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•If you have made a mistake while setting the timer, press CANCEL. (However, this does not always work. If CANCEL does not work, press CLOCK/TIMER repeatedly and start from step 1 again.)

On the unit:

1 Put a recordable cassette into deck B.

7 When selecting “– CD – – –”

1)Press SELECT – or SELECT + to select the disc number, then press SET.

2)Press SELECT – or SELECT + to set the track number, then press SET.

The unit enters volume setting mode.

When selecting “TUNER FM” or “TUNER AM”

Press SELECT – or SELECT + to select the preset station number, then press SET.

The unit enters volume setting mode.

– SELECT +

4

5

SET

8

2 Press CLOCK/TIMER until “REC” CLOCK/TIMER appears on the display.

The REC indicator also starts flashing on the display.

REC

•Each time you press the button, the timer setting mode changes as follows:

8 Press SELECT – or SELECT + to

 

– SELECT +

4

5

set the volume level.

 

 

• You can select the volume level from among four levels. If you select “ VOL – – –,” the volume is set to the last level when the unit has been turned off.

DAILY

9 Press SET to complete the Daily

SET

8

Timer setting.

 

The DAILY indicator stops flashing and

 

remains lit. The settings you have done are

 

shown on the display in sequence.

 

10 Press POWER to turn off the unit

POWER

(on standby) if you have set the

 

Daily Timer with the unit turned on.

 

DAILY ON TIME REC

Canceled

 

Clock

 

ON TIME

 

 

 

 

setting

 

 

(See page 11.)

 

3 Press CLOCK/TIMER again.

CLOCK/TIMER

“ON TIME” appears for 2 seconds, then the unit enters on-time setting mode.

REC

REC

– 24 –

Page 26 Page 28
Image 27
Page 26 Page 28
Contents MX-J300 MX-J200 Mises en garde, précautions et indications diverses For Canada/pour le Canada Precautions IntroductionAbout This Manual Contents CA-MXJ300 Location of the Buttons and ControlsPowered Rolling Panel CA-MXJ300 Front PanelDisplay Window CA-MXJ200 These buttons do not function as 1 / Á CA-MXJ200 Front PanelRemote Control Remote ControlFM antenna Connecting AntennasGetting Started UnpackingTo connect an outdoor AM antenna Connecting SpeakersRelease the finger from the clamp AM antennaTo start the display demonstration manually Connecting Other EquipmentPress and hold Demo for more than Seconds.DEMO To connect audio equipmentCommon Operations Setting the ClockAdjusting the Volume Turning On the Power and Selecting the SourcesSurround modes Reinforcing the Bass SoundSelecting the Sound Modes To select the sound modes, press SoundListening to FM and AM Broadcasts Tuning in a StationTuning in a Preset Station Presetting StationsBasic CD Operations Playing Back CDsLoading CDs Playing Back the Entire Discs Continuous PlayProgram Play Prepare CDs Select the Random play mode On the unitTo check the program contents Playing at Random Random PlayRepeating Tracks or CDs Repeat Play Prohibiting Disc Ejection Tray LockIf you try to eject CDs Playing Back a Tape Playing Back TapesStart recording On the unit Press REC START/STOP RecordingRecording Tapes on Deck B Press Eject 0for the deck BPress Dubbing To record on both sides Reverse ModeDubbing Tapes CD Direct RecordingUsing Daily Timer Using the TimersPress Timer When selecting CDWhen selecting Tuner FM or Tuner AM Press 4or ¢to set the volume levelHow Recording Timer actually works Using Recording TimerSet the volume level Timer settingPut a recordable cassette into deck B Press Shift To turn on On the remote controlPress Timer until REC appears Press Power to turn off the unit on standby if necessaryOn the remote control only Press Sleep Timer PriorityUsing Sleep Timer Select the preset stationMaintenance Handling discsCassette decks Specifications TroubleshootingHOW to Locate Your JVC Service Center Limited Warranty AUDIO-1 0200KSMMDWHIT
Top Page Image Contents