JVC RX-430VBK manual Connecting the Power Cord, Putting Batteries in the Remote Control

Page 14

English

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

1. Plug the power cord into an AC outlet.

POWER

2. Press POWER to set it in the _ON position.

The STANDBY lamp lights up. A small amount of power is always consumed.

_ON ÑOFF

To shut off the power completely:

Press POWER to set it in the ÑOFF position.

Keep the power cord away from the connecting cables for the TV, VCR, and antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

The difference between the POWER switch and the STANDBY/ON button

•The POWER switch is the mains supply switch, allowing the receiver to connect to the mains supply. To shut off the power completely, press the POWER switch to set it in the ÑOFF position.

•The STANDBY/ON button is a functional on/off (standby) switch, and does not disconnect the receiver from the mains supply. A small amount of power is consumed even in standby mode for the receiver to accept signals from the remote control.

Note:

The preset settings such as preset channel and sound adjustment may be erased in the following cases:

•When you press POWER to set it in the ÑOFF position.

•When you unplug the power cord.

•When a power failure occurs.

CAUTIONS:

•Do not touch the power cord with wet hands.

•Do not pull on the power cord to unplug the receiver. When unplugging the receiver, always grasp the plug itself so as not to damage the cord.

Putting Batteries in the Remote Control

Before using the remote control, put the two supplied batteries in first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.

1.On the back of the remote control, press down on the battery cover and slide it out.

2.Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (–) to (–).

3.Slide the cover.

R6P (SUM-3)/AA (15F)

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P (SUM-3)/ AA (15F) type dry-cell batteries.

CAUTIONS:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity indicated: (+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

Page 9

Page 13 Page 15
Image 14
Page 13 Page 15
Contents RX-430VBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-430VBK Table of Contents Front Panel Switches, Buttons and ControlsRemote Control Getting Started Before InstallationChecking the Supplied Accessories FM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna AM MW/LW Antenna ConnectionsConnecting the rear and center speakers Connecting the SpeakersConnecting the front speakers Case 3 When you connect front and rear speakers Case 1 When you connect only front speakersCase 2 When you connect front speakers and a center speaker About the speaker impedance of the speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Audio Components Video ComponentsVideo component connections VCRPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Press Power to set it in the on positionSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting the Front Speakers Adjusting the VolumeFrom the remote control only Muting the SoundListening with Headphones Recording a SourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep TimerLarge Selecting the Center Speaker SizeLarge Small no SmallTo cancel the One Touch Operation function Using the One Touch OperationTo store the sound settings Press ONE Touch Operation One Touch OperationStoring the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsFM Auto Selecting the FM Reception ModeTuning in a Preset Station FM MonoMovie Sports Music Using the Preset SEA ModesSelecting Your Favorite SEA Mode SPORTS1 SPORTS2 SPORTS3Movie 1 Movie 2 Movie Press Preset to select the effect levelMovie SPORTS2 Jazz What is surround? Using the Surround ProcessorUsing JVC’s Hall Surround Prologic 3CHLOGIC HallPress Rear +/- to adjust the rear speaker output level Delay 1 Delay 2 DelayDelay Press Delay to adjust the delay timeSpeaker Arrangements for Dolby Surround This casePreparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output balance as follows Left front Center Right front Speaker Rear speakersPress Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround LOGIC, Hall lights up on the displayAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingUsing the Remote Control SEA Surround Control ON/OFF Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierGeneral FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT 0497OFYOTKJEM

RX-430VBK specifications

The JVC RX-430VBK is a versatile stereo receiver that has captured the attention of audio enthusiasts and casual listeners alike. Designed for those who appreciate quality sound in a compact format, this receiver comes packed with features that enhance its functionality and audio performance.

One of the main highlights of the RX-430VBK is its power output, delivering a robust 100 watts per channel. This power capacity ensures clear and dynamic sound reproduction, making it suitable for a wide range of listening environments. Whether you are enjoying music, watching movies, or gaming, the RX-430VBK provides an immersive audio experience that brings your media to life.

The receiver features a built-in AM/FM tuner, allowing users to easily access their favorite radio stations. The tuner is equipped with a preset channel memory, letting users store up to 30 stations for quick access. This feature is especially convenient for those who enjoy a mix of local and national broadcasts.

For connectivity, the JVC RX-430VBK is well-equipped with multiple inputs and outputs, including five audio inputs and a dedicated phono input for turntables. This makes it an ideal choice for vinyl enthusiasts who want to connect their record player without the need for additional preamps. Additionally, it includes a headphone jack for private listening, as well as speaker outputs that support either A or B configurations, allowing for flexible setups.

Another standout feature of the RX-430VBK is its built-in digital signal processing (DSP). This technology enables users to tailor their audio experience with various sound modes such as Hall, Jazz, and Rock, which enhance the listening experience depending on the genre. The built-in EQ further allows for fine-tuning the audio output, helping users achieve their desired sound profile.

From a design perspective, the RX-430VBK boasts a sleek and modern aesthetic that fits comfortably into most home entertainment setups. Its user-friendly interface and remote control make it easy to navigate settings and manage playback from a distance.

In summary, the JVC RX-430VBK is a powerful and feature-rich stereo receiver that caters to a broad range of audio preferences and setups. With its solid power output, versatile connectivity options, and innovative sound technologies, it stands out as a strong choice for anyone looking to enhance their audio experience at home.
Top Page Image Contents