JVC RX-430VBK manual Connecting the FM and AM MW/LW Antennas, FM Antenna Connections

Page 9

Connecting the FM and AM (MW/LW) Antennas

FM Antenna Connections

A

B

ANTENNA

ANTENNA

75

75

FM

FM

COAXIAL

COAXIAL

GND

GND

AM

AM

LOOP

LOOP

ANTENNA

FM Antenna

 

FM 75

 

COAXIAL

 

GND

AM

Outdoor FM Antenna

 

LOOP

AM

 

 

EXT

English

AUsing the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75- ohm COAXIAL terminal as temporary measure.

BUsing the Standard Type Connector (Not Supplied) A standard type connector (IEC or DIN45325) should be connected to the FM 75-ohm COAXIAL terminal.

Note: Make sure the antenna conductors do not touch any other terminals, connecting cords or power cord. This could cause poor reception.

Extend the supplied FM antenna horizontally.

If reception is poor, connect an outdoor FM antenna.

Before attaching a 75-ohm coaxial cable (the kind with a round wire going to the outdoor FM antenna), disconnect the supplied FM antenna.

AM (MW/LW) Antenna Connections

ANTENNA

FM 75

COAXIAL

AM (MW/LW) Loop Antenna

GND

AM

LOOP

AM

EXT

Turn the loop until you have the best reception.

Snap the tabs on the loop into the slots of the base to assemble the AM (MW/LW) loop.

1

2

3

 

 

 

 

If reception is poor, connect an outdoor single vinyl-

 

 

 

covered wire to the AM EXT terminal. (Keep the AM

 

AM (MW/LW) Wire Antenna

(MW/LW) loop antenna connected.)

Note :

Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

Page 4

Image 9
Contents RX-430VBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-430VBK Table of Contents Switches, Buttons and Controls Remote ControlFront Panel Before Installation Checking the Supplied AccessoriesGetting Started Using the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Case 2 When you connect front speakers and a center speaker Case 1 When you connect only front speakersCase 3 When you connect front and rear speakers About the speaker impedance of the speakersConnecting the subwoofer speaker Connecting Audio/Video ComponentsAudio component connections Audio Components Video ComponentsVCR Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Press Power to set it in the on positionTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play From the remote control only Adjusting the VolumeSelecting the Front Speakers Muting the SoundRecording a Source Listening with HeadphonesAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Using the Sleep TimerLarge Small no Selecting the Center Speaker SizeLarge SmallTo store the sound settings Press ONE Touch Operation Using the One Touch OperationTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyStoring the preset stations Receiving Radio BroadcastsTuning in a Preset Station Selecting the FM Reception ModeFM Auto FM MonoSelecting Your Favorite SEA Mode Using the Preset SEA ModesMovie Sports Music SPORTS1 SPORTS2 SPORTS3Press Preset to select the effect level Movie SPORTS2 JazzMovie 1 Movie 2 Movie Using JVC’s Hall Surround Using the Surround ProcessorWhat is surround? Prologic 3CHLOGIC HallDelay Delay 1 Delay 2 DelayPress Rear +/- to adjust the rear speaker output level Press Delay to adjust the delay timeThis case Speaker Arrangements for Dolby SurroundWide Normal Phantom Preparing for Dolby SurroundLeft front Center Right front Speaker Rear speakers If necessary, adjust the speaker output balance as followsPress Test again to stop the test tone Press Test to start checking the speaker output balanceLOGIC, Hall lights up on the display Using Dolby SurroundRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingUsing the Remote Control SEA Surround Control ON/OFF Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT 0497OFYOTKJEM

RX-430VBK specifications

The JVC RX-430VBK is a versatile stereo receiver that has captured the attention of audio enthusiasts and casual listeners alike. Designed for those who appreciate quality sound in a compact format, this receiver comes packed with features that enhance its functionality and audio performance.

One of the main highlights of the RX-430VBK is its power output, delivering a robust 100 watts per channel. This power capacity ensures clear and dynamic sound reproduction, making it suitable for a wide range of listening environments. Whether you are enjoying music, watching movies, or gaming, the RX-430VBK provides an immersive audio experience that brings your media to life.

The receiver features a built-in AM/FM tuner, allowing users to easily access their favorite radio stations. The tuner is equipped with a preset channel memory, letting users store up to 30 stations for quick access. This feature is especially convenient for those who enjoy a mix of local and national broadcasts.

For connectivity, the JVC RX-430VBK is well-equipped with multiple inputs and outputs, including five audio inputs and a dedicated phono input for turntables. This makes it an ideal choice for vinyl enthusiasts who want to connect their record player without the need for additional preamps. Additionally, it includes a headphone jack for private listening, as well as speaker outputs that support either A or B configurations, allowing for flexible setups.

Another standout feature of the RX-430VBK is its built-in digital signal processing (DSP). This technology enables users to tailor their audio experience with various sound modes such as Hall, Jazz, and Rock, which enhance the listening experience depending on the genre. The built-in EQ further allows for fine-tuning the audio output, helping users achieve their desired sound profile.

From a design perspective, the RX-430VBK boasts a sleek and modern aesthetic that fits comfortably into most home entertainment setups. Its user-friendly interface and remote control make it easy to navigate settings and manage playback from a distance.

In summary, the JVC RX-430VBK is a powerful and feature-rich stereo receiver that caters to a broad range of audio preferences and setups. With its solid power output, versatile connectivity options, and innovative sound technologies, it stands out as a strong choice for anyone looking to enhance their audio experience at home.