JVC RX-5052S, RX-5050B Getting Started, Before Installation, Connecting the FM and AM Antennas

Page 6

Getting Started

Do not connect the AC power cord until all other connections have been made.

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

General Precautions

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture and dust.

•The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Notes:

•Supplied batteries are for the initial setup. Replace for continued use.

•After replacing the batteries, set the manufacturers’ codes again (see pages 30 and 31).

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity: (+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Connecting the FM and AM Antennas

FM antenna connections

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM Loop Antenna (1)

•FM Antenna (1)

If anything is missing, contact your dealer immediately.

Putting Batteries in the Remote Control

Before using the remote control, insert the two supplied batteries first.

1

2 R6(SUM-3)/

3

 

AA(15F)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Press and slide the battery cover on the back of the remote control.

2Insert the batteries.

• Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the remote control cannot transmit signals or operate the receiver correctly, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

AB

AM

 

AM

EXT

 

EXT

AM

AM

P

P

LOO

LOO

 

75

ANTENNA

75

ANTENNA

 

 

COAXIAL

 

COAXIAL

 

FM

 

FM

 

Extend the supplied FM antenna horizontally.

AM

EXT

AM

LOOP

FM Antenna (supplied)

FM 75

 

 

COAXIAL

 

Outdoor FM Antenna Cable

 

ANTENNA

 

(not supplied)

 

 

Connect the supplied FM antenna as temporary measure to the FM 75 Ω COAXIAL terminal—A

If reception is poor, connect the outdoor FM antenna (not supplied)—B

1Disconnect the supplied FM antenna.

2Connect a 75 Ω coaxial cable (with the standard type connector).

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents RX-5050B/RX-5052S LVT1290-001A JMises en garde, précautions et indications diverses Table of Contents Parts Identification Front PanelDisplay Remote Control Rear PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Putting Batteries in the Remote ControlAM antenna connections Connecting the Speakers and SubwooferConnecting the speakers Turn the loop until you have the best receptionAnalog Connections Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersVideo component connections To audio output To composite video inputDVD player Connecting the Power Cord Plug the power cord into an AC outletDigital Connections Daily Operational Procedure Selecting the Source to Play Turning On the PowerBasic Operations Sound Adjusting the VolumeWhen analog input is selected Always lights up Picture from a video component such as the VCR or DVDBe sure to turn down the volume Selecting the Analog or Digital Input ModeListening with headphones Press Subwoofer OUT ON/OFF to cancel the subwoofer outputChanging the Display Brightness When Dolby Digital or DTS Surround is selectedTo select the analog input mode Press DimmerMuting the Sound Using the Sleep TimerBasic adjustment auto memory Recording a sourceReceiving Radio Broadcasts Tuning in to Stations ManuallyUsing Preset Tuning Press FM/AM to select the band FM or AMWhile listening to an FM station, press FM Mode Press the 10 keys to select a preset channel numberSelecting the FM Reception Mode To tune in a preset stationChannel number Basic SettingsPress Quick Speaker Setup Press in Multi JOG Push SETBasic Setting Items Press SettingEx. When setting Auto Surround to Auto Surr on Setting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Selecting the Main or Sub Channel Select the playback sounds channelSelect Auto Surr on to activate Auto Surround Setting for Easy and Effective Surround OperationsSetting the Digital Input Terminals Select Vrtl SB on to activate Virtual Surround BackPress Adjust Adjusting SoundBasic Adjustment Items Ex. When adjusting the subwoofer level toAdjusting the Equalization Patterns Adjusting the Speaker Output LevelsDolby Digital*1 Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital 5.1CHDTS Digital Surround What is Linear PCM?What is Dual Mono? DTS 96/24Press Surround to activate the Surround mode Activating the Surround ModesSelect and play any source Introducing the DSP Modes Using the DSP ModesReproducing the Sound Field Digital Acoustic Processor DAP modesMulti-channel digital signals To cancel the DSP modeTo adjust the effect level except All Channel Stereo, see Activating the DSP ModesSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerDVD player Operating Video ComponentsCD changer Set TV/CATV selector to TVTry to operate your Catv converter by pressing If there are more than one code listed for your brand of TVRelease STANDBY/ON TV/CATV Try to operate your TV by pressingRelease STANDBY/ON DVD If there are more than one code listed for your brandRelease STANDBY/ON VCR Try to operate your VCR by pressingTroubleshooting Problem Possible Cause SolutionHz to 20 kHz with no more than 0.8% total SpecificationsPer channel, min. RMS, driven into 8 Ω Harmonic distortionFM tuner IHF AM tunerGeneral Page Page AUDIO/VIDEO Control Receiver LVT1290-002A C Mises en garde, précautions et indications diverses English RX-6030VAUDIO/VIDEO Control Receiver Remote Control Do not insert any metal object into the receiver Right Getting Started DVD player Connecting the Power Cord Basic Operations Basic Operations Turning On and Off Attenuating the Input Signal Muting the Sound Tuning in to Stations Manually Selecting the FM Reception Mode Basic Settings Basic Procedure Basic Settings Selecting the Main or Sub Channel Setting for Easy and Effective Surround Operations Adjusting Sound Adjusting Sound Using the Surround Modes Using the Surround Modes Activating the Surround Modes Using the DSP Modes Activating the DSP Modes Operating JVC’s Audio/Video Components Operating Video Components Operating Other Manufacturers’ Video Equipment STANDBY/ON VCR Subwoofer no Specifications Specifications EN, FR

RX-5052S, RX-5050B specifications

The JVC RX-5050B and RX-5052S are solid audio receivers that have appealed to home theater enthusiasts and casual listeners alike. Both models, known for their reliability and robust sound quality, present advanced features tailored for an immersive audio experience.

One of the standout features of the RX-5050B and RX-5052S is their high power output. These receivers are equipped with powerful amplification systems that permit them to deliver clear, dynamic sound across a wide range of frequencies. With a total harmonic distortion (THD) of less than 0.05%, these receivers ensure that the audio remains clean and true to the source material. This clarity allows listeners to appreciate subtle details in both music and movie soundtracks.

The RX-5050B and RX-5052S utilize JVC's proprietary technologies to enhance audio performance. This includes the Virtual Surround feature, which creates an expansive soundstage, making it feel as if sound is emanating from all around the listener. Furthermore, these models support a variety of audio formats, catering to diverse preferences from stereo sound to multi-channel audio setups.

Another key highlight of the RX-5050B and RX-5052S is their versatility with connectivity. Equipped with multiple inputs, including standard RCA connections, optical inputs, and coaxial inputs, these receivers can easily connect to a wide range of devices, such as DVD players, game consoles, and streaming devices. This versatility means that users can enjoy audio from various sources seamlessly.

In terms of build quality, both models feature a sturdy design that contributes to their longevity. The user interface is straightforward, allowing for easy navigation through settings and adjustments. The front panel includes a large volume knob, an AM/FM tuner, and dedicated buttons for essential functions, providing an intuitive experience for users of all ages.

Whether you're a movie buff looking to enhance your home theater setup or a music lover wanting to enjoy your favorite albums with pristine sound, the JVC RX-5050B and RX-5052S stand out as excellent choices. Their combination of power, sound processing technology, and ease of use make them reliable components in any audio setup. With the durability and performance offered by these receivers, users can expect a satisfying auditory experience for many years to come.
Top Page Image Contents