JVC LVT1140-004A Connecting Audio/Video Components, Connecting the subwoofer, Placing speakers

Page 11

	Connecting the subwoofer	Connecting Audio/Video Components
	You can enhance the bass by connecting a subwoofer.	Connecting Audio/Video Components
	You can enhance the bass by connecting a subwoofer.
	Connect the input jack of a powered subwoofer to the rear panel,	When connecting individual components, refer also to the manuals
	using a cable with RCA pin plugs (not supplied).	supplied with them.

English

SUBWOOFER

OUT

Powered subwoofer

Placing speakers

Front speakers (L/R) and center speaker (C)

•Place these speakers at the same height from the floor, at or near ear level.

•Array across the front of the viewing area.

Surround speakers (LS/RS)

•Place these speakers alongside and slightly to the rear of (but not behind) the listening position; well above ear level (60 cm to 90 cm higher).

•Point these speakers directly across the listening area, but not at the listener’s ears.

Subwoofer (S.WFR)

•You can place it wherever you like since bass sound is non- directional. Normally place it in front of you.

L R

C

45– 60

S.WFR

LS

RS

After connecting the speakers, set the speaker installation information properly. You can use Quick Speaker Setup for it (see page 18).

Analog Connections

Audio component connections

Use the cables with RCA pin plugs (not supplied).

•Connect the white plug to the audio left jack, and the red plug to the audio right jack.

If your audio components have a COMPU LINK jack

See also page 30 for detailed information about the connection and the COMPU LINK remote control system.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

CD player

CD player

	R
	CD
	IN
To audio	L
To audio
output
Cassette deck/CD recorder

Cassette deck or CD recorder

To audio input To audio output

L

R

OUT

(REC)

TAPE

/CDR L

IN

(PLAY)

R

Note:

When connecting a CD recorder to the TAPE/CDR jacks, change the source name to “CDR,” which will be shown on the display when it is selected as the source. See page 14 for details.

7

Image 11

Contents LVT1140-004A US RX-6042S RX-5042SPrecaución--Interruptor STANDBY/ON Precaución Precaución Ventilación Adecuada Table of Contents Front Panel Parts IdentificationDisplay Remote ControlRX-5042S Rear PanelRX-6042S Putting Batteries in the Remote Control Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesTurn the loop until you have the best reception Connecting the Speakers and SubwooferConnecting the speakers AM antenna connectionsAnalog Connections Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersGreen Red BlueDVD player When you connect a DVD player with stereo output jacksDigital Connections Adjusting the Voltage SelectorConnecting the Power Cord Plug the power cord into an AC outletBasic Operations Daily Operational Procedure Selecting the Source to PlayTurning On the Power Sound Adjusting the VolumePress Subwoofer OUT ON/OFF to cancel the subwoofer output Selecting the Analog or Digital Input ModeListening with headphones Be sure to turn down the volumePress Dimmer When Dolby Digital or DTS Surround is selectedTo select the analog input mode Changing the Display BrightnessRecording a source Basic adjustment auto memoryReinforcing the Bass Muting the SoundSelect the band FM or AM Using Preset TuningReceiving Radio Broadcasts Press MemoryTo tune in a preset station Press the 10 keys to select a preset channel numberSelecting the FM Reception Mode While listening to an FM station, press FM ModePress in Multi JOG Push SET Basic SettingsPress Quick Speaker Setup Channel numberEx. When setting Auto Surround to Auto Surr on Basic Setting ItemsPress Setting Setting the Bass Sounds Setting the SpeakersSetting the Speaker Distance Select Auto Surr on to activate Auto Surround Setting for Easy and Effective Surround OperationsSelecting the Main or Sub Channel Select the playback sounds channelSelect Vrtl SB on to activate Virtual Surround Back Setting the Digital Input TerminalsSetting the Component Video Input This setting is only for RX-6042SEx. When adjusting the subwoofer level to Adjusting SoundBasic Adjustment Items Press AdjustAdjusting the Speaker Output Levels Adjusting the Equalization PatternsDolby Digital 5.1CH Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital*1DTS 96/24 What is Linear PCM?What is Dual Mono? DTS Digital SurroundSelect and play any source excluding DVD Multi for RX-6042S Press Surround to activate the Surround modeActivating the Surround Modes Digital Acoustic Processor DAP modes Using the DSP ModesReproducing the Sound Field Introducing the DSP ModesActivating the DSP Modes To cancel the DSP modeMulti-channel digital signals To adjust the effect level except All Channel Stereo, seeAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerConnections 2 Video Cable Connection AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection One-Touch Video Play Connecting procedureAutomatic Selection of TV’s Input Mode Automatic Power On/Off StandbyPress CD-DISC, then press Press CD, then press +10 Operating JVC’s Audio/Video ComponentsOperating Audio Components Cassette deck Operating Video ComponentsCD recorder DVD playerTry to operate your Catv converter by pressing If there are more than one code listed for your brand of TVRelease STANDBY/ON TV/CATV Try to operate your TV by pressingTry to operate your VCR by pressing If there are more than one code listed for your brandRelease STANDBY/ON VCR Release STANDBY/ON DVDProblem Possible Cause Solution TroubleshootingModels Output/Input terminals Sources Functions Main differences between the modelsAudio VideoPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA