JVC LVT1140-004A manual Adjusting Sound, Basic Adjustment Items, Press Adjust

Page 27

Adjusting Sound

You can make sound adjustment to your preference after completing basic settings.

English

Basic Adjustment Items

On the following pages, you can adjust the following items:

•You can adjust only the items applicable to the current sound mode.

Items	To do	See page
DEQ 63HZ	Adjust equalizer pattern at 63 Hz.		24

DEQ250HZ	Adjust equalizer pattern at 250 Hz.		24

DEQ 1KHZ	Adjust equalizer pattern at 1 kHz.		24

DEQ 4KHZ	Adjust equalizer pattern at 4 kHz.		24

DEQ16KHZ	Adjust equalizer pattern at 16 kHz.		24

SUBWFR LEVEL	Adjust the subwoofer output level.		24

FRONT L LEVEL	Adjust the left front speaker output
	level.		24

FRONT R LEVEL	Adjust the right front speaker output
	level.		24

CENTER LEVEL	Adjust the center speaker output
	level.		24

SURR L LEVEL	Adjust the left surround speaker
	output level.		24

SURR R LEVEL	Adjust the right surround speaker
	output level.		24

EFFECT*1	Adjust the effect level.		24
CENTER TONE*2	Make the center tone soft or sharp.		24
PANORAMA CTRL*3 Add “wraparound” sound effect with
	side-wall image.		24

Basic Procedure	Remote
	NOT

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Ex. When adjusting the subwoofer level to “–3”.

1 Press ADJUST.

The last selected item appears on the display.

2Turn MULTI JOG until an item you want appears on the display.

•In this example, select “SUBWFR LEVEL.” For available items, see the list “Basic Adjustment Items.”

			3	Press in MULTI JOG (PUSH SET).
Notes:				The current setting (or level) for the selected item appears on the
*1	Adjustable when one of the DAP modes or Mono Film (see pages			display.
*1
	28 and 29) is in use.
*2	This setting is only for RX-6042S.
*3	Adjustable when Pro Logic II Music is in use.

			4	Turn MULTI JOG to select a setting you want or
				to make an adjustment as you like.

5 Press in MULTI JOG (PUSH SET).

6 Repeat steps 2 to 5 to set other items if necessary.

7 Press EXIT.

The source indication resumes on the display.

23

Image 27

Contents LVT1140-004A US RX-6042S RX-5042SPrecaución--Interruptor STANDBY/ON Precaución Precaución Ventilación Adecuada Table of Contents Front Panel Parts IdentificationDisplay Remote ControlRear Panel RX-6042SRX-5042S Putting Batteries in the Remote Control Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesTurn the loop until you have the best reception Connecting the Speakers and SubwooferConnecting the speakers AM antenna connectionsAnalog Connections Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersGreen Red BlueDVD player When you connect a DVD player with stereo output jacksDigital Connections Adjusting the Voltage SelectorConnecting the Power Cord Plug the power cord into an AC outletDaily Operational Procedure Selecting the Source to Play Turning On the PowerBasic Operations Sound Adjusting the VolumePress Subwoofer OUT ON/OFF to cancel the subwoofer output Selecting the Analog or Digital Input ModeListening with headphones Be sure to turn down the volumePress Dimmer When Dolby Digital or DTS Surround is selectedTo select the analog input mode Changing the Display BrightnessRecording a source Basic adjustment auto memoryReinforcing the Bass Muting the SoundSelect the band FM or AM Using Preset TuningReceiving Radio Broadcasts Press MemoryTo tune in a preset station Press the 10 keys to select a preset channel numberSelecting the FM Reception Mode While listening to an FM station, press FM ModePress in Multi JOG Push SET Basic SettingsPress Quick Speaker Setup Channel numberBasic Setting Items Press SettingEx. When setting Auto Surround to Auto Surr on Setting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Select Auto Surr on to activate Auto Surround Setting for Easy and Effective Surround OperationsSelecting the Main or Sub Channel Select the playback sounds channelSelect Vrtl SB on to activate Virtual Surround Back Setting the Digital Input TerminalsSetting the Component Video Input This setting is only for RX-6042SEx. When adjusting the subwoofer level to Adjusting SoundBasic Adjustment Items Press AdjustAdjusting the Speaker Output Levels Adjusting the Equalization PatternsDolby Digital 5.1CH Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital*1DTS 96/24 What is Linear PCM?What is Dual Mono? DTS Digital SurroundPress Surround to activate the Surround mode Activating the Surround ModesSelect and play any source excluding DVD Multi for RX-6042S Digital Acoustic Processor DAP modes Using the DSP ModesReproducing the Sound Field Introducing the DSP ModesActivating the DSP Modes To cancel the DSP modeMulti-channel digital signals To adjust the effect level except All Channel Stereo, seeAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerAV Compu Link Remote Control System Connections 1 AV Compu Link ConnectionConnections 2 Video Cable Connection One-Touch Video Play Connecting procedureAutomatic Selection of TV’s Input Mode Automatic Power On/Off StandbyOperating JVC’s Audio/Video Components Operating Audio ComponentsPress CD-DISC, then press Press CD, then press +10 Cassette deck Operating Video ComponentsCD recorder DVD playerTry to operate your Catv converter by pressing If there are more than one code listed for your brand of TVRelease STANDBY/ON TV/CATV Try to operate your TV by pressingTry to operate your VCR by pressing If there are more than one code listed for your brandRelease STANDBY/ON VCR Release STANDBY/ON DVDProblem Possible Cause Solution TroubleshootingModels Output/Input terminals Sources Functions Main differences between the modelsAudio VideoPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA