JVC LVT1140-004A manual Basic Operations, Daily Operational Procedure Selecting the Source to Play

Page 15

Basic Operations

The following operations are commonly used when you play any sound sources.

Operations hereafter will be explained using the buttons on the front panel.

You can also use the buttons on the remote control for the same functions if they have the same and similar names/marks.

Daily Operational Procedure

Selecting the Source to Play

English

1Turn on the power.

•See “Turning On the Power” below.

2Select the source.

•See “Selecting the Source to Play” to the right.

3Adjust the volume.

•See “Adjusting the Volume” on page 12.

4Select the Surround or DSP modes.

•See “Activating the Surround Modes” (page 27) and “Activating the DSP Modes” (page 29).

Turning On the Power

Press STANDBY/ON (or STANDBY/ON AUDIO on the remote control).

The STANDBY lamp goes off.

Current source name appears.

VOLUME

Current volume level appears.

To turn off the power (into standby mode),

press STANDBY/ON (or STANDBY/ON AUDIO on the remote control) again.

The STANDBY lamp lights up.

Note:

A small amount of power is consumed in standby mode. To turn off

the power completely, unplug the AC power cord.

When you have connected digital source components using the digital terminals, first change the input mode for these components to the digital input mode (see page 13).

Press one of the source selection buttons.

Selected source name appears.

VOLUME

For RX-6042S

DVD MULTI	DVD	VCR	TV SOUND	CD	TAPE/CDR	FM	AM
					SOURCE NAME
		On the front panel
		TAPE/CDR	CD	DVD	DVD MULTI
		FM/AM	TV SOUND	VCR

On the remote

Note:

When you select “DVD MULTI,” you can enjoy analog discrete output sound (5.1-channel surround reproduction) from the external component.

•You may need to select analog discrete output mode on the external component.

•When using the headphones, you can listen to the front channel sounds (left and right) only.

•Surround and DSP modes (see pages 25 and 28) cannot be applied to “DVD MULTI.”

For RX-5042S

DVD	VCR	TV SOUND	CD	TAPE/CDR	FM/AM

SOURCE NAME

On the front panel

TAPE/CDR CD DVD

FM/AM TV SOUND VCR

On the remote

Note:

When connecting a CD recorder to the TAPE/CDR jacks, change the

source name shown on the display. For details, see page 14.

11

Image 15

Contents LVT1140-004A US RX-6042S RX-5042SPrecaución--Interruptor STANDBY/ON Precaución Precaución Ventilación Adecuada Table of Contents Front Panel Parts IdentificationDisplay Remote ControlRear Panel RX-6042SRX-5042S Putting Batteries in the Remote Control Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesTurn the loop until you have the best reception Connecting the Speakers and SubwooferConnecting the speakers AM antenna connectionsAnalog Connections Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersGreen Red BlueDVD player When you connect a DVD player with stereo output jacksDigital Connections Adjusting the Voltage SelectorConnecting the Power Cord Plug the power cord into an AC outletDaily Operational Procedure Selecting the Source to Play Turning On the PowerBasic Operations Sound Adjusting the VolumePress Subwoofer OUT ON/OFF to cancel the subwoofer output Selecting the Analog or Digital Input ModeListening with headphones Be sure to turn down the volumePress Dimmer When Dolby Digital or DTS Surround is selectedTo select the analog input mode Changing the Display BrightnessRecording a source Basic adjustment auto memoryReinforcing the Bass Muting the SoundSelect the band FM or AM Using Preset TuningReceiving Radio Broadcasts Press MemoryTo tune in a preset station Press the 10 keys to select a preset channel numberSelecting the FM Reception Mode While listening to an FM station, press FM ModePress in Multi JOG Push SET Basic SettingsPress Quick Speaker Setup Channel numberBasic Setting Items Press SettingEx. When setting Auto Surround to Auto Surr on Setting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Select Auto Surr on to activate Auto Surround Setting for Easy and Effective Surround OperationsSelecting the Main or Sub Channel Select the playback sounds channelSelect Vrtl SB on to activate Virtual Surround Back Setting the Digital Input TerminalsSetting the Component Video Input This setting is only for RX-6042SEx. When adjusting the subwoofer level to Adjusting SoundBasic Adjustment Items Press AdjustAdjusting the Speaker Output Levels Adjusting the Equalization PatternsDolby Digital 5.1CH Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital*1DTS 96/24 What is Linear PCM?What is Dual Mono? DTS Digital SurroundPress Surround to activate the Surround mode Activating the Surround ModesSelect and play any source excluding DVD Multi for RX-6042S Digital Acoustic Processor DAP modes Using the DSP ModesReproducing the Sound Field Introducing the DSP ModesActivating the DSP Modes To cancel the DSP modeMulti-channel digital signals To adjust the effect level except All Channel Stereo, seeAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerAV Compu Link Remote Control System Connections 1 AV Compu Link ConnectionConnections 2 Video Cable Connection One-Touch Video Play Connecting procedureAutomatic Selection of TV’s Input Mode Automatic Power On/Off StandbyOperating JVC’s Audio/Video Components Operating Audio ComponentsPress CD-DISC, then press Press CD, then press +10 Cassette deck Operating Video ComponentsCD recorder DVD playerTry to operate your Catv converter by pressing If there are more than one code listed for your brand of TVRelease STANDBY/ON TV/CATV Try to operate your TV by pressingTry to operate your VCR by pressing If there are more than one code listed for your brandRelease STANDBY/ON VCR Release STANDBY/ON DVDProblem Possible Cause Solution TroubleshootingModels Output/Input terminals Sources Functions Main differences between the modelsAudio VideoPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA