JVC LVT1140-004A manual Operating JVC’s Audio/Video Components, Operating Audio Components

Page 37

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control.

English

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using the supplied remote control:

•You need to connect JVC’s audio components through the COMPU LINK (SYNCHRO) jacks (see page 30) in addition to the connections using cables with RCA pin plugs (see page 7).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selection buttons on the remote control.

•To operate the target component using the COMPU LINK remote control system, set the source name correctly if required. (See page 14.)

•Refer also to the manuals supplied with your components.

Sound control section (Amplifier)

You can always perform the following operations:

STANDBY/ON

AUDIO:

 

Turn on or off the receiver.

VOLUME +/–:

Adjust the volume level.

MUTING:

Turn on or off sound muting.

ANALOG/DIGITAL: Switch the analog and digital input

 

alternately.

DIMMER:

Dim or brighten the display.

SLEEP:

Set the Sleep Timer.

SURROUND:

Turn on and select Surround modes.

DSP:

Turn on and select DSP modes.

SURROUND/DSP OFF:

 

Turn off the Surround and DSP mode.

BASSBOOST:

Only for RX-6042S: Turn on or off Bass

 

Boost.

After pressing SOUND, you can perform the following operations by using the 10 keys:

FRONT L then LEVEL +/–:Adjust the left front speaker output

level.

FRONT R then LEVEL +/–:Adjust the right front speaker output

level.

CENTER then LEVEL +/–: Adjust the center speaker output level.

SURR L then LEVEL +/–: Adjust the left surround speaker output level.

SURR R then LEVEL +/–: Adjust the right surround speaker output level.

SUBWFR then LEVEL +/–: Adjust the subwoofer output level.

EFFECT:

Adjust the effect level.

TEST:

Turn on or off test tone output.

Note:

After adjusting sounds, press the corresponding source selection button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

Tuner

You can always perform the following operations:

FM/AM: Alternate between FM and AM.

After pressing FM/AM, you can perform the following operations on a tuner:

1 – 10, +10: Select a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

FM MODE: Change the FM reception mode.

CD player

After pressing CD, you can perform the following operations on a CD player:

3:

Start playing.

4:

Return to the beginning of the current (or previous)

 

track.

¢:

Skip to the beginning of the next track.

7:

Stop playing.

8:

Pause playing. To resume, press 3.

1 – 10, +10: Select a track number directly. For track number 5, press 5.

For track number 15, press +10, then 5. For track number 20, press +10, then 10.

For track number 30, press +10, +10, then 10.

CD changer

After pressing CD-DISC, you can perform the following operations on a CD changer:

3:

Start playing.

4:

Return to the beginning of the current (or previous)

 

track.

¢:

Skip to the beginning of the next track.

7:

Stop playing.

8:

Pause playing. To resume, press 3.

1 – 6, 7/P:

Select the number of a disc installed in a CD

 

changer.

After pressing CD, you can perform the following operations on a CD changer:

1 – 10, +10: Select a track number directly. For track number 5, press 5.

For track number 15, press +10, then 5. For track number 20, press +10, then 10.

For track number 30, press +10, +10, then 10.

Example:

•Selecting disc number 4, track number 12, and starting playback.

1 Press CD-DISC, then press 4.

2 Press CD, then press +10, 2.

Continued on the next page

33

Page 36 Page 38
Image 37
Page 36 Page 38
Contents LVT1140-004A US RX-6042S RX-5042SPrecaución--Interruptor STANDBY/ON Precaución Precaución Ventilación Adecuada Table of Contents Front Panel Parts IdentificationDisplay Remote ControlRX-6042S Rear PanelRX-5042S Connecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Putting Batteries in the Remote ControlConnecting the speakers Connecting the Speakers and SubwooferAM antenna connections Turn the loop until you have the best receptionConnecting the subwoofer Connecting Audio/Video ComponentsPlacing speakers Analog ConnectionsGreen Red BlueDVD player When you connect a DVD player with stereo output jacksConnecting the Power Cord Adjusting the Voltage SelectorPlug the power cord into an AC outlet Digital ConnectionsTurning On the Power Daily Operational Procedure Selecting the Source to PlayBasic Operations Sound Adjusting the VolumeListening with headphones Selecting the Analog or Digital Input ModeBe sure to turn down the volume Press Subwoofer OUT ON/OFF to cancel the subwoofer outputTo select the analog input mode When Dolby Digital or DTS Surround is selectedChanging the Display Brightness Press DimmerReinforcing the Bass Basic adjustment auto memoryMuting the Sound Recording a sourceReceiving Radio Broadcasts Using Preset TuningPress Memory Select the band FM or AMSelecting the FM Reception Mode Press the 10 keys to select a preset channel numberWhile listening to an FM station, press FM Mode To tune in a preset stationPress Quick Speaker Setup Basic SettingsChannel number Press in Multi JOG Push SETPress Setting Basic Setting ItemsEx. When setting Auto Surround to Auto Surr on Setting the Speaker Distance Setting the SpeakersSetting the Bass Sounds Selecting the Main or Sub Channel Setting for Easy and Effective Surround OperationsSelect the playback sounds channel Select Auto Surr on to activate Auto SurroundSetting the Component Video Input Setting the Digital Input TerminalsThis setting is only for RX-6042S Select Vrtl SB on to activate Virtual Surround BackBasic Adjustment Items Adjusting SoundPress Adjust Ex. When adjusting the subwoofer level toAdjusting the Speaker Output Levels Adjusting the Equalization PatternsReproducing Theater Ambience Introducing the Surround Modes Using the Surround ModesDolby Digital*1 Dolby Digital 5.1CHWhat is Dual Mono? What is Linear PCM?DTS Digital Surround DTS 96/24Activating the Surround Modes Press Surround to activate the Surround modeSelect and play any source excluding DVD Multi for RX-6042S Reproducing the Sound Field Using the DSP ModesIntroducing the DSP Modes Digital Acoustic Processor DAP modesMulti-channel digital signals To cancel the DSP modeTo adjust the effect level except All Channel Stereo, see Activating the DSP ModesRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemPress the play 3 button on the CD player Automatic Source SelectionConnections 1 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 2 Video Cable Connection Automatic Selection of TV’s Input Mode Connecting procedureAutomatic Power On/Off Standby One-Touch Video PlayOperating Audio Components Operating JVC’s Audio/Video ComponentsPress CD-DISC, then press Press CD, then press +10 CD recorder Operating Video ComponentsDVD player Cassette deckRelease STANDBY/ON TV/CATV If there are more than one code listed for your brand of TVTry to operate your TV by pressing Try to operate your Catv converter by pressingRelease STANDBY/ON VCR If there are more than one code listed for your brandRelease STANDBY/ON DVD Try to operate your VCR by pressingProblem Possible Cause Solution TroubleshootingAudio Main differences between the modelsVideo Models Output/Input terminals Sources FunctionsPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA
Top Page Image Contents