JVC RX-8012VSL Operating Video Components, VCR 1 VCR connected to the VCR 1 jacks, DVD player

English

Operating Video Components

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC video components through the AV COMPU LINK jacks (see page 47) in addition to the connections using cables with RCA pin plugs (see pages 6 and 7).

•Some JVC VCRs can accept two types of the control signals — remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR 1 jacks is set to code “A.”

–When another JVC VCR is connected to the VCR 2 or VIDEO terminals, set its remote control code to code “B.” (This remote control cannot emit the control signals of code “B.”)

•When using the remote control:

–For the DVD player and VCR 1 operations, aim the remote control directly at the remote sensor on each component, not on the receiver.

–For the TV having the AV COMPU LINK EX or AV COMPU LINK III terminal, aim the remote control directly at the remote sensor on the TV.

CATV/DBS	VCR 1	TV	AUDIO
DVD	DVD MUILTI	CD	FM/AM
TV/DBS	VIDEO	CDR	PHONO
VCR 1	VCR 2	TAPE/MD	USB
SURROUND	DSP ANALOG/DIGITAL		SLEEP
ON/OFF	MODE	INPUT
	BASS		ROOM
LINEDIF.ECT	BOOST	EFFECT	SIZE
	1	2	3
MIDNIGHT		MENU
MODE	TEST	CTRTONE	LIVENESS
	4	5	6
	∗SUBWFR	ENTER
SOUND		∗L/R BAL	∗CENTER
	7/P	8	9
MUTING ∗DIGITALEQ ∗REARL			∗REARR
	10	0	+10
	RETURN	FMMODE	100+
CATV/DBS	+∗BAL L +
CONTROL			+
TV/VIDEO	CH/∗LEVEL TV VOL		VOLUME
	−∗BAL R −		−
MENU		PLAY	EXIT
TEXT	/REW	PAUSE	FF/
DISPLAY
		SET
REC	DOWN – TUNING – UP
PAUSE
		STOP	CONTROL

RM-SRX8012U

A/V CONTROL RECEIVER

Note:

When you press one of the following buttons mentioned in this section, the operation mode appears on the display window for about 10 seconds. For example, above illustration shows that you have pressed VCR 1.

Buttons	Indications
VCR 1	VCR 1
DVD or DVD MULTI	DVD
TV/DBS	TV
CONTROL (repeatedly)	VCR 1	TAPE
	CDDSC	CDR

VCR 1 (VCR connected to the VCR 1 jacks)

You can always perform the following operations:

VCR 1 : Turns on or off the VCR 1.

After pressing VCR 1 (or selecting “VCR 1” by pressing CONTROL repeatedly), you can perform the following operations on the VCR 1:

1 – 9, 0:	Selects the TV channels on the VCR.
3PLAY:	Starts playing.
REW:	Rewinds a tape.
FF:	Fast winds a tape.
7 STOP:	Stops operations.
8 PAUSE:	Pauses playing. To release it, press
REC PAUSE:	3PLAY.
	Enters recording pause.
CH +/–:	Changes the TV channels on the VCR.

Note:

You can use either VCR 1 or CONTROL to activate the buttons listed above. If you press VCR 1, the playing source also changes. On the other hand, if you press CONTROL repeatedly to select “VCR 1,” the playing source does not change.

DVD player

After pressing DVD or DVD MULTI, you can perform the following operations on a DVD player:

3PLAY:			Starts playing.
4:			Returns to the beginning of the current
¢:			(or previous) track.
			Skips to the beginning of the next track.
7 STOP:			Stops playing.
8 PAUSE:			Stops playing temporarily. To release it,
			press 3 PLAY.
	After pressing DVD or DVD			EFFECT	ROOM
					SIZE
	MULTI, these buttons can be used
				2	3
	for the DVD menu operations.
				MENU
			TEST	CTR TONE	LIVENESS
Note:			4	5	6
				ENTER
				∗L/R BAL
For detailed menu operations, refer to
				8
	the instructions supplied with the
	discs or the DVD player.
TV
You can always perform the following operations:
TV		:	Turns on or off the TV.
TV VOL +/–:			Adjusts the volume.
TV/VIDEO:			Sets the input mode (either TV or
			VIDEO).

After pressing TV/DBS, you can perform the following operations on a TV:

CH +/–:	Changes the channels.
1 – 9, 0, 100+:	Selects the channels.
RETURN:	Alternates between the previously
	selected channel and the current
	channel.

51