JVC RX-630RBK manual Connecting the FM and AM MW/LW Antennas, FM Antenna Connections

Page 10

English

Connecting the FM and AM (MW/LW) Antennas

FM Antenna Connections

A

B

 

ANTENNAFM

ANTENNA

75

75

FM

COAXIAL

COAXIAL

GND

 

GND

AM

AM

 

LOOP

LOOP

 

ANTENNA

FM Antenna

FM 75

COAXIAL

 

GND

AM

Outside FM Antenna Wire

LOOP

AM

 

 

EXT

A

B

Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75- ohm COAXIAL terminal as temporary measure.

Using the Standard Type Connector (Not Supplied)

A standard type connector (IEC or DIN45325) should be connected to the FM 75-ohm COAXIAL terminal.

Note: Make sure the antenna conductors do not touch any other terminals, connecting cords or power cord. This could cause poor reception.

Extend the FM wire antenna horizontally.

If reception is poor, connect the outside antenna.

Before attaching a 75-ohm coaxial cable (the kind with a round wire going to the outdoor FM antenna), disconnect the supplied FM antenna.

AM (MW/LW) Antenna Connections

ANTENNA

FM 75

COAXIAL

AM (MW/LW) Loop Antenna

GND

AM

LOOP

AM

EXT

Turn the loop until you have the best reception.

Snap the tabs on the loop into the slots of the base to assemble the AM (MW/LW) loop.

1

2

3

 

 

 

 

If reception is poor, connect an outdoor single vinyl-

 

 

 

covered wire to the AM EXT terminal. (Keep the AM

 

AM (MW/LW) Wire Antenna

(MW/LW) loop antenna connected.)

Note:

Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

Page 5

Image 10
Contents RX-630RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-630RBK Table of Contents Checking the Supplied Accessories Before InstallationGetting Started Front Panel Switches, Buttons and ControlsFront Panel Remote Control Remote ControlUsing the Standard Type Connector Not Supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersOpen the terminal Connecting the rear and center speakersConnecting the subwoofer speaker Close the terminalCase 2 When you connect front speakers and a center speaker Case 1 When you connect only front speakersCase 3 When you connect front and rear speakers About the speaker impedance of the speakersAudio Components Video Components Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalPress Power to set it in the on position Connecting the Power CordPlug the power cord into an AC outlet To shut off the power completelyPutting Batteries in the Remote Control R6PSUM-3/AA 15FBasic Operations Turning the Power On and OffSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeOn the front panel only Muting the Sound Listening with HeadphonesRecording a Source Listening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance FunctionTo cancel the Sleep Timer Using the Sleep TimerWhen the shut-off time comes From the remote control Press Sleep repeatedlyLarge Selecting the Center Speaker SizeLarge Small SmallOne Touch Operation Using the One Touch OperationAbout the One Touch Operation Storing the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsAuto Selecting the FM Reception ModeTuning in a preset station MonoPress Control % / Þto select a character Assigning Names to Preset StationsWhen a character you want appears, press Control #or @ Available charactersWhat Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsPTY Searching for a Program by PTY Codes Affairs AlarmNews InfoTA NEWS/INFO TA/INFO TA/NEWS News Info TA/NEWS/INFO Switching to a Broadcast Program of Your Choice TemporarilyCase Selecting Your Favorite SEA Mode Using the SEA ModesRock Musical Movie Country SEA OFF Usermode Jazz To recall your own SEA adjustment Creating Your Own SEA ModeAdjust the SEA frequency and its level To erase a stored adjustmentWhat is surround? Using the Surround ProcessorUsing JVC’s Hall Surround Prologic 3CHLOGIC Hall Surr OFFPress Mode repeatedly until Hall appears on the display Delay 1 Delay Delay 4 DelayDelay Press Rear +/- to adjust the rear speaker output levelWhen you have added a center speaker without rear speakers When you have added rear speakers without a center speakerSpeaker Arrangements for Dolby Surround Preparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output level as follows DelaySOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTo operate JVC’s audio components using this remote control Enter button after selecting a channel number Troubleshooting Problem Possible Cause SolutionAmplifier SpecificationsVideo AM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT 0697OFYOTKJEM

RX-630RBK specifications

The JVC RX-630RBK is a versatile and powerful stereo receiver designed to enhance your home audio experience. With a sleek and modern design, it fits seamlessly into any entertainment setup while providing robust sound quality and an array of features.

One of the main highlights of the RX-630RBK is its solid power output, delivering 100 watts per channel across a wide frequency range. This ensures that whether you're listening to music, watching movies, or playing video games, the audio experience is both rich and immersive. The receiver also supports both stereo and multi-channel formats, making it an excellent choice for various audio sources.

The RX-630RBK incorporates advanced technologies to optimize sound performance. It features a built-in FM/AM tuner with 30 preset stations, allowing you to easily access your favorite radio channels. The receiver also has a dedicated phono input, enabling audiophiles to connect their turntables and enjoy vinyl records with clarity and depth. Additionally, it supports digital audio inputs, including optical and coaxial connections, ensuring compatibility with modern devices.

User-friendly controls and a remote make it easy to navigate through various settings and audio sources. The LCD display provides clear information about current settings, making adjustments straightforward. The receiver is equipped with multiple audio inputs, including auxiliary and USB ports, allowing you to connect smartphones, tablets, or other audio sources effortlessly.

Another notable feature of the JVC RX-630RBK is its adjustable equalizer settings. This allows users to fine-tune the audio output to suit their preferences or the acoustics of their room. Bass and treble adjustments ensure that you can enjoy music and other audio content exactly as you like it.

The RX-630RBK also prioritizes safety, featuring built-in protection circuits to prevent overheating and overload, ensuring longevity and reliability.

In summary, the JVC RX-630RBK is a powerful and feature-rich stereo receiver offering exceptional sound quality and versatile connectivity options. Its combination of advanced technology, user-friendly controls, and thoughtful features make it an ideal choice for audio enthusiasts looking to elevate their listening experience at home. With the RX-630RBK, enjoying high-fidelity sound has never been easier or more accessible.