JVC RX-630RBK manual Basic Operations, Turning the Power On and Off, Selecting the Source to Play

Page 17

Basic Operations

The following operations are commonly used when you play any sound source.

Turning the Power On and Off

 

On the front panel:

STANDBY

To turn on the power, press STANDBY/ON .

 

The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the

 

display.

English

STANDBY/ON

Current source name appears

STANDBY

100

1k

10k

VOLUME

Volume level is also shown here whenever the power is on.

STANDBY/ON

Front panel

AUDIO

Remote Control

To turn off the power (into standby mode), press STANDBY/ON again.

The STANDBY lamp lights up.

From the remote control:

To turn on the power, press AUDIO .

The STANDBY lamp goes off. The name of the current source appears on the display.

To turn off the power (into standby mode), press AUDIO again.

The STANDBY lamp lights up.

Note:

Pressing STANDBY/ON or AUDIO again turns off the power (into standby mode) and lights the STANDBY lamp. A small amount of power is consumed in standby mode. To turn the power off completely,

press POWER to set it in the ÑOFF position on the front panel.

Selecting the Source to Play

You need to select the source before you start playing any source.

On the front panel:

1. Press SOURCE so that the Control %/ Þbuttons work for selecting the source.

SOURCE

2.Press Control % / Þuntil the source name you want appears on the display. The selected source lamp also lights up.

Selected source name appears

Front panel

MUTE AUTO

TUNED

STEREO

EON

TA NEWS INFO

FM

 

 

 

 

SLEEP

AM

 

 

 

 

 

CH–

 

 

 

 

MHz

 

 

 

 

kHz

 

 

SURROUND PRO LOGIC 3CH LOGIC HALL

 

 

 

SEA

LOUDNESS

100

1k

10k

 

 

VOLUME

Page 12

Image 17
Contents RX-630RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-630RBK Table of Contents Getting Started Before InstallationChecking the Supplied Accessories Front Panel Switches, Buttons and ControlsFront Panel Remote Control Remote ControlUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasUsing the Standard Type Connector Not Supplied FM Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the subwoofer speaker Connecting the rear and center speakersOpen the terminal Close the terminalCase 3 When you connect front and rear speakers Case 1 When you connect only front speakersCase 2 When you connect front speakers and a center speaker About the speaker impedance of the speakersAudio component connections Connecting Audio/Video ComponentsAudio Components Video Components If your audio components have a Compu LINK-3 terminalPlug the power cord into an AC outlet Connecting the Power CordPress Power to set it in the on position To shut off the power completelyR6PSUM-3/AA 15F Putting Batteries in the Remote ControlSelecting the Source to Play Turning the Power On and OffBasic Operations On the front panel only Adjusting the VolumeSelecting the Front Speakers Recording a Source Listening with HeadphonesMuting the Sound Adjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness FunctionWhen the shut-off time comes Using the Sleep TimerTo cancel the Sleep Timer From the remote control Press Sleep repeatedlyLarge Small Selecting the Center Speaker SizeLarge SmallAbout the One Touch Operation Using the One Touch OperationOne Touch Operation Using Preset Tuning Tuning in Stations ManuallyStoring the preset stations Receiving Radio BroadcastsTuning in a preset station Selecting the FM Reception ModeAuto MonoWhen a character you want appears, press Control #or @ Assigning Names to Preset StationsPress Control % / Þto select a character Available charactersPTY Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes News AlarmAffairs InfoCase Switching to a Broadcast Program of Your Choice TemporarilyTA NEWS/INFO TA/INFO TA/NEWS News Info TA/NEWS/INFO Rock Musical Movie Country SEA OFF Usermode Jazz Using the SEA ModesSelecting Your Favorite SEA Mode Adjust the SEA frequency and its level Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing JVC’s Hall Surround Using the Surround ProcessorWhat is surround? Prologic 3CHLOGIC Hall Surr OFFDelay Delay 1 Delay Delay 4 DelayPress Mode repeatedly until Hall appears on the display Press Rear +/- to adjust the rear speaker output levelSpeaker Arrangements for Dolby Surround When you have added rear speakers without a center speakerWhen you have added a center speaker without rear speakers Wide Normal Phantom Preparing for Dolby SurroundSOFT2 SOFT1 Flat SHARP1 SHARP2 DelayIf necessary, adjust the speaker output level as follows Press Test again to stop the test tone Press Test to start checking the speaker output balanceUsing Dolby Surround Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingTo operate JVC’s audio components using this remote control Enter button after selecting a channel number Problem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier General FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT 0697OFYOTKJEM

RX-630RBK specifications

The JVC RX-630RBK is a versatile and powerful stereo receiver designed to enhance your home audio experience. With a sleek and modern design, it fits seamlessly into any entertainment setup while providing robust sound quality and an array of features.

One of the main highlights of the RX-630RBK is its solid power output, delivering 100 watts per channel across a wide frequency range. This ensures that whether you're listening to music, watching movies, or playing video games, the audio experience is both rich and immersive. The receiver also supports both stereo and multi-channel formats, making it an excellent choice for various audio sources.

The RX-630RBK incorporates advanced technologies to optimize sound performance. It features a built-in FM/AM tuner with 30 preset stations, allowing you to easily access your favorite radio channels. The receiver also has a dedicated phono input, enabling audiophiles to connect their turntables and enjoy vinyl records with clarity and depth. Additionally, it supports digital audio inputs, including optical and coaxial connections, ensuring compatibility with modern devices.

User-friendly controls and a remote make it easy to navigate through various settings and audio sources. The LCD display provides clear information about current settings, making adjustments straightforward. The receiver is equipped with multiple audio inputs, including auxiliary and USB ports, allowing you to connect smartphones, tablets, or other audio sources effortlessly.

Another notable feature of the JVC RX-630RBK is its adjustable equalizer settings. This allows users to fine-tune the audio output to suit their preferences or the acoustics of their room. Bass and treble adjustments ensure that you can enjoy music and other audio content exactly as you like it.

The RX-630RBK also prioritizes safety, featuring built-in protection circuits to prevent overheating and overload, ensuring longevity and reliability.

In summary, the JVC RX-630RBK is a powerful and feature-rich stereo receiver offering exceptional sound quality and versatile connectivity options. Its combination of advanced technology, user-friendly controls, and thoughtful features make it an ideal choice for audio enthusiasts looking to elevate their listening experience at home. With the RX-630RBK, enjoying high-fidelity sound has never been easier or more accessible.