JVC RX-630RBK manual Connecting Audio/Video Components, Audio component connections

Page 14

English

Connecting Audio/Video Components

You can connect the following audio/video components to this receiver using cables with RCA pin plugs (not supplied). Refer also to the manuals supplied with your components. If you want to connect a component not listed in the table below, refer to the manual supplied with it.

Audio Components

Video Components

 

 

 

 

Turntable

TV

 

 

 

 

CD player

VCR

 

 

 

 

Cassette deck

Video disc player

 

 

 

 

Notes:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

Any turntables incorporating a small-output cartridge such as an MC (moving-coil type) must be connected to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result in insufficient volume.

Audio component connections

If a ground wire is provided for your turntable, connect the cable to the screw marked GND on the rear panel.

To audio output

CD player

Cassette deck

GND

To audio output

To audio input

To audio output

AUDIO

RIGHT LEFT

PHONO

CD

OUT

(REC)

VCR VCR

IN

(PLAY)

VIDEO VIDEO

TV

SOUND MONITOR

OUT

OUT

(REC)

TAPE

IN

(PLAY)

Turntable

VIDEO

OUT

(REC)

IN

(PLAY)

If your audio components have a COMPU LINK-3 terminal

The COMPU LINK remote control system allows you to control other JVC audio components from the receiver or vice versa.

Connect your audio components and the receiver with the cable (monaural mini-plug supplied with those components) as well as the connection above.

For detailed information about the connection and the COMPU LINK-3 remote control system, see page 35.

Note:

The COMPU LINK-3 remote control system is the upgraded version of the COMPU LINK-1 and COMPU LINK-2. Even if your component has the COMPU LINK-1 or COMPU LINK-2 jacks, you can still connect it in the COMPU LINK-3 remote control system, but some functions may not work correctly.

Page 9

Image 14
Contents RX-630RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-630RBK Table of Contents Getting Started Before InstallationChecking the Supplied Accessories Front Panel Switches, Buttons and ControlsFront Panel Remote Control Remote ControlUsing the Standard Type Connector Not Supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersOpen the terminal Connecting the rear and center speakersConnecting the subwoofer speaker Close the terminalCase 2 When you connect front speakers and a center speaker Case 1 When you connect only front speakersCase 3 When you connect front and rear speakers About the speaker impedance of the speakersAudio Components Video Components Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalPress Power to set it in the on position Connecting the Power CordPlug the power cord into an AC outlet To shut off the power completelyPutting Batteries in the Remote Control R6PSUM-3/AA 15FSelecting the Source to Play Turning the Power On and OffBasic Operations On the front panel only Adjusting the VolumeSelecting the Front Speakers Recording a Source Listening with HeadphonesMuting the Sound Listening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance FunctionTo cancel the Sleep Timer Using the Sleep TimerWhen the shut-off time comes From the remote control Press Sleep repeatedlyLarge Selecting the Center Speaker SizeLarge Small SmallAbout the One Touch Operation Using the One Touch OperationOne Touch Operation Storing the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsAuto Selecting the FM Reception ModeTuning in a preset station MonoPress Control % / Þto select a character Assigning Names to Preset StationsWhen a character you want appears, press Control #or @ Available charactersPTY Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes Affairs AlarmNews InfoCase Switching to a Broadcast Program of Your Choice TemporarilyTA NEWS/INFO TA/INFO TA/NEWS News Info TA/NEWS/INFO Rock Musical Movie Country SEA OFF Usermode Jazz Using the SEA ModesSelecting Your Favorite SEA Mode To recall your own SEA adjustment Creating Your Own SEA ModeAdjust the SEA frequency and its level To erase a stored adjustmentWhat is surround? Using the Surround ProcessorUsing JVC’s Hall Surround Prologic 3CHLOGIC Hall Surr OFFPress Mode repeatedly until Hall appears on the display Delay 1 Delay Delay 4 DelayDelay Press Rear +/- to adjust the rear speaker output levelSpeaker Arrangements for Dolby Surround When you have added rear speakers without a center speakerWhen you have added a center speaker without rear speakers Preparing for Dolby Surround Wide Normal PhantomSOFT2 SOFT1 Flat SHARP1 SHARP2 DelayIf necessary, adjust the speaker output level as follows Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingTo operate JVC’s audio components using this remote control Enter button after selecting a channel number Troubleshooting Problem Possible Cause SolutionVideo SpecificationsAmplifier General FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT 0697OFYOTKJEM

RX-630RBK specifications

The JVC RX-630RBK is a versatile and powerful stereo receiver designed to enhance your home audio experience. With a sleek and modern design, it fits seamlessly into any entertainment setup while providing robust sound quality and an array of features.

One of the main highlights of the RX-630RBK is its solid power output, delivering 100 watts per channel across a wide frequency range. This ensures that whether you're listening to music, watching movies, or playing video games, the audio experience is both rich and immersive. The receiver also supports both stereo and multi-channel formats, making it an excellent choice for various audio sources.

The RX-630RBK incorporates advanced technologies to optimize sound performance. It features a built-in FM/AM tuner with 30 preset stations, allowing you to easily access your favorite radio channels. The receiver also has a dedicated phono input, enabling audiophiles to connect their turntables and enjoy vinyl records with clarity and depth. Additionally, it supports digital audio inputs, including optical and coaxial connections, ensuring compatibility with modern devices.

User-friendly controls and a remote make it easy to navigate through various settings and audio sources. The LCD display provides clear information about current settings, making adjustments straightforward. The receiver is equipped with multiple audio inputs, including auxiliary and USB ports, allowing you to connect smartphones, tablets, or other audio sources effortlessly.

Another notable feature of the JVC RX-630RBK is its adjustable equalizer settings. This allows users to fine-tune the audio output to suit their preferences or the acoustics of their room. Bass and treble adjustments ensure that you can enjoy music and other audio content exactly as you like it.

The RX-630RBK also prioritizes safety, featuring built-in protection circuits to prevent overheating and overload, ensuring longevity and reliability.

In summary, the JVC RX-630RBK is a powerful and feature-rich stereo receiver offering exceptional sound quality and versatile connectivity options. Its combination of advanced technology, user-friendly controls, and thoughtful features make it an ideal choice for audio enthusiasts looking to elevate their listening experience at home. With the RX-630RBK, enjoying high-fidelity sound has never been easier or more accessible.