JVC RX-630RBK manual Searching for a Program by PTY Codes

Page 28

English

FM/AM

 

PTY+

\

DISPLAY

PTY

MODE

PTY– SEARCH

Remote control

When pressing DISPLAY MODE on the remote control:

Make sure that you have selected FM station using the remote control only.

If not, the DISPLAY MODE button does not work for tuner operation. (Pressing FM/AM activates the remote control for tuner operation.)

Notes:

If searching finishes at once, “PS”, “PTY”, and “RT” will not appear on the display.

If you press DISPLAY MODE while listening to an AM (MW/LW) station, the display only shows station frequency.

RDS is not available for AM (MW/LW) broadcasts.

Searching for a Program by PTY Codes

One of the advantages of the RDS service is that you can locate a particular kind of program from the preset channels by specifying the PTY codes.

To search for a program using the PTY codes

On the front panel:

PTY SEARCH

1. Press PTY SEARCH while listening to an FM station so that Control @/ # buttons work for

 

selecting PTY code.

“PTY” and “SELECT” alternate on the display.

2.Press Control @/ # until the PTY code you want appears on the display.

Each time you press the button, the display gives you the PTY codes described on page 24.

3.Press PTY SEARCH again.

While searching, “SEARCH” and the selected PTY code alternate on the display.

The receiver searches 40 preset channels, stops when it finds the one you have selected, and tunes in that station.

PTY SEARCH

Front panel

To continue searching after the first stop

Press PTY SEARCH again while the indications on the display are flashing. If no program is found, “NOTFOUND” appears on the display.

To stop searching any time during the process

Press PTY SEARCH while searching.

Page 23

Image 28
Contents RX-630RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-630RBK Table of Contents Checking the Supplied Accessories Before InstallationGetting Started Front Panel Switches, Buttons and ControlsFront Panel Remote Control Remote ControlConnecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaUsing the Standard Type Connector Not Supplied FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the rear and center speakers Connecting the subwoofer speakerOpen the terminal Close the terminalCase 1 When you connect only front speakers Case 3 When you connect front and rear speakersCase 2 When you connect front speakers and a center speaker About the speaker impedance of the speakersConnecting Audio/Video Components Audio component connectionsAudio Components Video Components If your audio components have a Compu LINK-3 terminalConnecting the Power Cord Plug the power cord into an AC outletPress Power to set it in the on position To shut off the power completelyPutting Batteries in the Remote Control R6PSUM-3/AA 15FBasic Operations Turning the Power On and OffSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeOn the front panel only Muting the Sound Listening with HeadphonesRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness FunctionUsing the Sleep Timer When the shut-off time comesTo cancel the Sleep Timer From the remote control Press Sleep repeatedlySelecting the Center Speaker Size Large SmallLarge SmallOne Touch Operation Using the One Touch OperationAbout the One Touch Operation Tuning in Stations Manually Using Preset TuningStoring the preset stations Receiving Radio BroadcastsSelecting the FM Reception Mode Tuning in a preset stationAuto MonoAssigning Names to Preset Stations When a character you want appears, press Control #or @Press Control % / Þto select a character Available charactersWhat Information Can RDS Signals Provide? Using the RDS Radio Data System to Receive FM StationsPTY Searching for a Program by PTY Codes Alarm NewsAffairs InfoTA NEWS/INFO TA/INFO TA/NEWS News Info TA/NEWS/INFO Switching to a Broadcast Program of Your Choice TemporarilyCase Selecting Your Favorite SEA Mode Using the SEA ModesRock Musical Movie Country SEA OFF Usermode Jazz Creating Your Own SEA Mode Adjust the SEA frequency and its levelTo recall your own SEA adjustment To erase a stored adjustmentUsing the Surround Processor Using JVC’s Hall SurroundWhat is surround? Prologic 3CHLOGIC Hall Surr OFFDelay 1 Delay Delay 4 Delay DelayPress Mode repeatedly until Hall appears on the display Press Rear +/- to adjust the rear speaker output levelWhen you have added a center speaker without rear speakers When you have added rear speakers without a center speakerSpeaker Arrangements for Dolby Surround Preparing for Dolby Surround Wide Normal PhantomIf necessary, adjust the speaker output level as follows DelaySOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingTo operate JVC’s audio components using this remote control Enter button after selecting a channel number Troubleshooting Problem Possible Cause SolutionAmplifier SpecificationsVideo AM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT 0697OFYOTKJEM

RX-630RBK specifications

The JVC RX-630RBK is a versatile and powerful stereo receiver designed to enhance your home audio experience. With a sleek and modern design, it fits seamlessly into any entertainment setup while providing robust sound quality and an array of features.

One of the main highlights of the RX-630RBK is its solid power output, delivering 100 watts per channel across a wide frequency range. This ensures that whether you're listening to music, watching movies, or playing video games, the audio experience is both rich and immersive. The receiver also supports both stereo and multi-channel formats, making it an excellent choice for various audio sources.

The RX-630RBK incorporates advanced technologies to optimize sound performance. It features a built-in FM/AM tuner with 30 preset stations, allowing you to easily access your favorite radio channels. The receiver also has a dedicated phono input, enabling audiophiles to connect their turntables and enjoy vinyl records with clarity and depth. Additionally, it supports digital audio inputs, including optical and coaxial connections, ensuring compatibility with modern devices.

User-friendly controls and a remote make it easy to navigate through various settings and audio sources. The LCD display provides clear information about current settings, making adjustments straightforward. The receiver is equipped with multiple audio inputs, including auxiliary and USB ports, allowing you to connect smartphones, tablets, or other audio sources effortlessly.

Another notable feature of the JVC RX-630RBK is its adjustable equalizer settings. This allows users to fine-tune the audio output to suit their preferences or the acoustics of their room. Bass and treble adjustments ensure that you can enjoy music and other audio content exactly as you like it.

The RX-630RBK also prioritizes safety, featuring built-in protection circuits to prevent overheating and overload, ensuring longevity and reliability.

In summary, the JVC RX-630RBK is a powerful and feature-rich stereo receiver offering exceptional sound quality and versatile connectivity options. Its combination of advanced technology, user-friendly controls, and thoughtful features make it an ideal choice for audio enthusiasts looking to elevate their listening experience at home. With the RX-630RBK, enjoying high-fidelity sound has never been easier or more accessible.