JVC RX-665VBK manual Recording a Source, Listening with Headphones, To listen with only headphones

Page 19

Recording a Source

You can record any source playing through the receiver to a cassette deck connected to the TAPE jacks and the VCR connected to the VCR jacks at the same time.

While recording, you can listen to the selected sound source at whatever sound level you like, without affecting the sound levels of the recording.

Listening with Headphones

English

Note:

The following sound modes cannot affect the recording.

•Preset SEA modes: (see page 24)

•3D-PHONIC modes: (see page

27)

•DAP modes: (see page 29)

•DVD MULTI playback mode: (see page 38)

A standard pair of headphones can be connected to the PHONES jack on the front panel. Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

To listen with only headphones

Press both SPEAKERS 1 and 2 to set them in the —OFF position.

SPEAKERS

12

_ON —OFF

Note:

The setting of the SPEAKERS 1 and 2 buttons does affect only the sound output of the front speakers.

16

Page 18 Page 20
Image 19
Page 18 Page 20
Contents RX-665VBK Mises en garde, précautions et indications diverses Niveau d’effet For actual setting procedures, see pages 26 toTable of Contents Front Panel Remote Control$ Power buttons CATV/SAT, TV, VCR Audio 14, 45, 46 Parts IdentificationFor Reproducing Surround Sound with your VCR Easy Set Up & OperationsTurn on the power For Reproducing DVD Multi Playback with your DVD player Easy Set Up & OperationsMake further Handling the receiver Getting StartedGeneral LocationsFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connect the front speakers to the Front Speakers terminals Connecting the front speakersConnecting the Speakers Getting StartedConnecting the subwoofer Connecting the rear and center speakersIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsAudio component connections Video component connectionsIf your audio components have an AV Compu Link terminal DVD player connectionPutting Batteries in the Remote Control Connecting the Power CordOn the front panel From the remote controlTurning the Power On and Off Basic OperationsBasic Operations From the remote control onlyOn the front panel only To listen with only headphones Listening with HeadphonesRecording a Source Using the Sleep Timer Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume LoudnessTo cancel the Sleep Timer When the shut-off time comesReceiver turns off automatically Large Basic SettingsSelecting the Center Speaker Size SmallOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsTo tune in a preset station To cancel a stored preset stationPress 10 keys to select a preset channel number Receiving Radio Broadcasts Selecting the FM Reception ModeSelecting Your Favorite SEA Mode Using the Preset SEA ModesTo cancel the preset SEA mode Press SEA Preset to select the effect level Using the Preset SEA ModesOn surround modes Using the Surround ProcessorOn JVC 3D-PHONIC mode On the DAP mode3DTHEATR Using the Surround ProcessorUsing JVC 3D-PHONIC Modes 3DACTIONPress Effect to select the effect level Press Control 2/ 3to adjust the effect levelTo cancel the 3D-PHONIC mode MarkPavilion Using the DAP ModesHall Select OFF in step DAP indicator goes off from the display To cancel the DAP modePress Rear L +/- to adjust the rear speaker Output level Effect This case Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode Speaker Arrangements for Surround ModesTheater Preparing for Surround ModesPress Surround so that the Control PrologicNormal Press Control 2/ 3to select the center modeDelay WideDelay 1 Delay 2 Delay If necessary, adjust the speaker output balance as followsPress Test to start checking the speaker output balance Press Effect to adjust the effect levelPress Test again to stop the test tone From the front panel Using Surround ModesTo cancel Surround mode Previous mode is recalled with its previousSpeaker arrangements for DVD Multi playback Using the DVD Multi Playback ModeActivating the DVD Multi playback Using the DVD Multi Playback Mode Synchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionConnect to the terminal indicated Illustration AV Compu Link Remote Control SystemDo not connect to the TV terminal One-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off See page 44 for detailsStarts playback To operate JVC audio components using this remote controlOperating Other Components Starts playingAfter pressing VCR, you can perform To operate JVC video components using this remote controlFollowing operations on the VCR TV/VIDEO TV Volume +Return CATV/SAT in the Power Press and hold CATV/SAT in the Power sectionEnter manufacturer’s code two digits using Release CATV/SAT in the Power sectionOperating Other Manufacturers’ Video Equipment Press and hold VCR in the Power sectionRelease VCR in the Power section Try to operate your VCR by pressing VCR PowerProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM tuner FM tuner IHFGeneral EN, FR

RX-665VBK specifications

The JVC RX-665VBK is a versatile and feature-rich audio receiver that has earned recognition for its balanced performance and modern connectivity options. Designed for home theater enthusiasts and music lovers alike, this receiver delivers a powerful audio experience while seamlessly integrating into your existing entertainment setup.

One of the standout features of the RX-665VBK is its robust amplification system. With a total output power of 100 watts per channel, it provides ample power to drive a wide range of speakers, making it suitable for various room sizes. The receiver employs direct energy technology, which enhances efficiency and minimizes distortion, resulting in clear and dynamic sound reproduction across all frequencies.

Connectivity is a strong point for the RX-665VBK, as it comes equipped with multiple HDMI inputs. This allows users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices, all while supporting high-definition video formats. Additionally, the receiver features a dedicated HDMI out for easy connection to your television, ensuring that you can enjoy high-quality audio-visual content without complicating your setup.

Incorporating advanced digital processing technologies, the RX-665VBK supports Dolby Digital and DTS surround sound formats. This enables users to experience immersive audio that complements high-definition video, making it perfect for movie nights and gaming sessions. The receiver also includes a built-in AM/FM tuner, allowing you to listen to your favorite radio stations with ease.

User convenience is further enhanced by the inclusion of an intuitive on-screen display. This feature simplifies the setup process, guiding users through the configuration of speaker settings and audio adjustments. For added flexibility, the RX-665VBK supports multiple audio input options, including USB and auxiliary inputs, enabling seamless playback from various sources.

The JVC RX-665VBK is not just about audio performance; its sleek and modern design ensures it fits well in any living space. With a user-friendly remote control, managing your audio experience is simple and straightforward.

In conclusion, the JVC RX-665VBK stands as a commendable choice for anyone seeking an affordable yet powerful audio receiver. With its combination of impressive amplification, advanced technologies, and modern connectivity options, it caters to the diverse needs of home entertainment enthusiasts, making it a valuable addition to any audio setup.
Top Page Image Contents