JVC RX-665VBK manual Receiving Radio Broadcasts, Tuning in Stations Manually, Using Preset Tuning

Page 24

English

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

Tuning in Stations Manually

On the front panel only:

TUNER/BAND

1. Press TUNER/BAND.

The lamp above the button lights up.

Each time you press the button, the band alternates between FM and AM.

2. Press Control 5 / ∞until “–TUNING+” appears on the display.

3. Press Control 2 / 3until you find the frequency you want.

• Pressing Control 2decreases the frequency.

• Pressing Control 3increases the frequency.

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 40 stations at random.

To store the preset stations

On the front panel only:

1.Tune in the station you want to preset (see above). If you want to store the FM reception mode for this station, select the FM reception mode you want. See page 23 for details.

2. Press MEMORY.

MEMORY

The channel number starts flashing on the display for about 5 seconds.

3. Press Control 2 / 3to select a channel number while the channel number position is flashing.

• Pressing Control 2decreases the number.

• Pressing Control 3increases the number.

4. Press MEMORY again while the selected channel

Notes:

•When you hold down Control 2 / 3 in step 3, the frequency keeps changing until you press Control 2 / 3again or a station is tuned in.

•When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.

When an FM stereo program is received, the STEREO indicator also lights up.

CAUTION:

Preset stations may be erased in a few days when power is cut off to the receiver, as when it is unplugged from the AC outlet or a power failure occurs. If the preset stations are lost, simply set the stations again.

Note:

You can press 10 keys on the remote control to select a channel number in step 3, if you have

number is flashing on the display.

MEMORY

pressed TUNER/BAND on the

The selected channel number stops flashing.

The station is assigned to the selected channel number.

remote control prior to starting this preset procedures.

•For channel number 5, press 5.

•For channel number 15, press +10 then 5.

•For channel number 20, press +10 then 10.

•For channel number 30, press +10, +10, then 10.

21

Page 23 Page 25
Image 24
Page 23 Page 25
Contents RX-665VBK Mises en garde, précautions et indications diverses For actual setting procedures, see pages 26 to Niveau d’effetTable of Contents Remote Control $ Power buttons CATV/SAT, TV, VCR Audio 14, 45, 46Parts Identification Front PanelEasy Set Up & Operations For Reproducing Surround Sound with your VCRTurn on the power Easy Set Up & Operations For Reproducing DVD Multi Playback with your DVD playerMake further Getting Started GeneralLocations Handling the receiverConnecting the FM and AM Antennas FM Antenna ConnectionsAM Antenna Connections Connecting the front speakers Connecting the SpeakersGetting Started Connect the front speakers to the Front Speakers terminalsConnecting the rear and center speakers Connecting the subwooferConnecting Audio/Video Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminalDVD player connection If your audio components have an AV Compu Link terminalConnecting the Power Cord Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and OffBasic Operations On the front panelFrom the remote control only Basic OperationsOn the front panel only Listening with Headphones To listen with only headphonesRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep TimerWhen the shut-off time comes To cancel the Sleep TimerReceiver turns off automatically Basic Settings Selecting the Center Speaker SizeSmall LargeTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Selecting the FM Reception Mode Receiving Radio BroadcastsUsing the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect levelUsing the Surround Processor On JVC 3D-PHONIC modeOn the DAP mode On surround modesUsing the Surround Processor Using JVC 3D-PHONIC Modes3DACTION 3DTHEATRPress Control 2/ 3to adjust the effect level To cancel the 3D-PHONIC modeMark Press Effect to select the effect levelUsing the DAP Modes PavilionHall To cancel the DAP mode Select OFF in step DAP indicator goes off from the displayPress Rear L +/- to adjust the rear speaker Output level Effect Select Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This casePreparing for Surround Modes Press Surround so that the ControlPrologic TheaterPress Control 2/ 3to select the center mode DelayWide NormalIf necessary, adjust the speaker output balance as follows Delay 1 Delay 2 DelayPress Effect to adjust the effect level Press Test to start checking the speaker output balancePress Test again to stop the test tone Using Surround Modes To cancel Surround modePrevious mode is recalled with its previous From the front panelUsing the DVD Multi Playback Mode Speaker arrangements for DVD Multi playbackActivating the DVD Multi playback Using the DVD Multi Playback Mode Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingAV Compu Link Remote Control System Connect to the terminal indicated IllustrationDo not connect to the TV terminal Automatic Selection of TV’s Input Mode Automatic Power On/OffSee page 44 for details One-Touch Video PlayTo operate JVC audio components using this remote control Operating Other ComponentsStarts playing Starts playbackTo operate JVC video components using this remote control After pressing VCR, you can performFollowing operations on the VCR TV Volume + TV/VIDEOReturn Press and hold CATV/SAT in the Power section Enter manufacturer’s code two digits usingRelease CATV/SAT in the Power section CATV/SAT in the PowerPress and hold VCR in the Power section Release VCR in the Power sectionTry to operate your VCR by pressing VCR Power Operating Other Manufacturers’ Video EquipmentTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM tunerGeneral EN, FR

RX-665VBK specifications

The JVC RX-665VBK is a versatile and feature-rich audio receiver that has earned recognition for its balanced performance and modern connectivity options. Designed for home theater enthusiasts and music lovers alike, this receiver delivers a powerful audio experience while seamlessly integrating into your existing entertainment setup.

One of the standout features of the RX-665VBK is its robust amplification system. With a total output power of 100 watts per channel, it provides ample power to drive a wide range of speakers, making it suitable for various room sizes. The receiver employs direct energy technology, which enhances efficiency and minimizes distortion, resulting in clear and dynamic sound reproduction across all frequencies.

Connectivity is a strong point for the RX-665VBK, as it comes equipped with multiple HDMI inputs. This allows users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices, all while supporting high-definition video formats. Additionally, the receiver features a dedicated HDMI out for easy connection to your television, ensuring that you can enjoy high-quality audio-visual content without complicating your setup.

Incorporating advanced digital processing technologies, the RX-665VBK supports Dolby Digital and DTS surround sound formats. This enables users to experience immersive audio that complements high-definition video, making it perfect for movie nights and gaming sessions. The receiver also includes a built-in AM/FM tuner, allowing you to listen to your favorite radio stations with ease.

User convenience is further enhanced by the inclusion of an intuitive on-screen display. This feature simplifies the setup process, guiding users through the configuration of speaker settings and audio adjustments. For added flexibility, the RX-665VBK supports multiple audio input options, including USB and auxiliary inputs, enabling seamless playback from various sources.

The JVC RX-665VBK is not just about audio performance; its sleek and modern design ensures it fits well in any living space. With a user-friendly remote control, managing your audio experience is simple and straightforward.

In conclusion, the JVC RX-665VBK stands as a commendable choice for anyone seeking an affordable yet powerful audio receiver. With its combination of impressive amplification, advanced technologies, and modern connectivity options, it caters to the diverse needs of home entertainment enthusiasts, making it a valuable addition to any audio setup.
Top Page Image Contents