JVC RX-6010VBK manual Adjusting the Surround Modes

Page 24
D I G I T A L
DOLBY SURROUND

English

Adjusting the Surround Modes

Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.

Dolby and DTS Surround adjustments

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 12).

5.Adjust the speaker output levels.

•To adjust the center speaker level, press CENTER +/– (from +10 dB to –10 dB).

•To adjust the left rear speaker level, press REAR•L +/– (from +10 dB to –10 dB).

•To adjust the right rear speaker level, press REAR•R +/– (from +10 dB to –10 dB).

– CENTER +

5 6

– REAR•L +

8 9

MENU

– REAR•R +

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 3 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NO.” See page 12.

• You cannot adjust the center speaker output level when you have

set “CENTER SPK” to “NO.” See page 12.

From the remote control:

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND to activate an

SURROUND

appropriate Surround mode —

 

PRO LOGIC, DOLBY DIGITAL

SURROUND

MODE

or DTS SURROUND.

 

When “PRO LOGIC” is selected,

the PRO LOGIC indicator lights up on the display.

•Each time you press the button, the Surround mode turns on and off alternately.

Note:

You can also press SURROUND MODE to activate an appropriate

Surround mode — PRO LOGIC, DOLBY DIGITAL, or DTS

SURROUND.

3. Press SOUND.

SOUND

 

The 10 keys are activated for sound adjustments.

4. Press TEST to check the speaker

TEST

1

output balance.

 

10 +10

ENTER

6. Press TEST again to stop the test

TEST

1

tone.

 

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with DOLBY SURROUND mark.

• To enjoy Dolby Digital, play back a software encoded with

Dolby Digital and labeled with mark.

D I G I T A L

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to

SURROUND ON/OFF

 

activate an appropriate Surround

 

mode — PRO LOGIC, DOLBY

 

DIGITAL or DTS SURROUND.

 

When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

•Each time you press the button, the Surround mode turns on and off alternately.

3.Adjust the speaker output levels.

1) Press ADJUST repeatedly until one of

ADJUST SETTING

the following indications appears on

 

the display.

 

 

“TEST TONE L” starts flashing on the

 

 

 

 

 

display, and a test tone comes out of the

 

 

 

 

 

speakers in the following order:

 

 

 

 

 

 

TEST TONE L

 

TEST TONE C

 

TEST TONE R

 

 

(Left front speaker)

 

(Center speaker)

 

(Right front speaker)

 

 

TEST TONE LS

TEST TONE RS

 

 

(Left rear speaker)

 

(Right rear speaker)

 

 

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NO” (see page 12).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page 12).

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from +10 dB to –10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

CONTROL

DOWN UP

21

Page 23 Page 25
Image 24
Page 23 Page 25
Contents RX-6010VBK Mises en garde, précautions et indications diverses English Français Table of Contents Remote Control Parts IdentificationFront Panel Before Installation Checking the Supplied AccessoriesConnecting the FM and AM Antennas Getting StartedConnecting the Speakers Basic connecting procedureConnecting the front speakers Connecting the rear and center speakersConnecting Audio/Video Components Connecting the subwoofer speakerAnalog connections Audio component connectionsVideo component connections DVD playerTo audio Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Digital connectionsTurning the Power On and Off Standby From the remote controlSignal and speaker indicators on the display Basic OperationsListening Only with Headphones Through all speakers and headphones ConnectedMuting the Sound Press Muting to mute the soundAdjusting the Subwoofer Output Level Adjusting the ToneAttenuating the Input Signal Basic Settings Recording a Source Setting the Subwoofer InformationAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Speakers for the DSP Modes Center Delay appears on DisplayRear Delay appears on Display To select the delay time of the rear speaker outputCrossover FRQ Crossover Frequency appears on the display LFE ATT Low Frequency Effect Attenuator appears on DisplayTo select the low frequency effect attenuator level Digital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeStoring the Basic Settings Adjustments Using the Sleep TimerChange the input mode Press Sleep repeatedlyTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Using the DSP Modes What are the DSP Modes?Surround modes Available DSP modes according to the input mode Reproducing the Sound FieldDAP modes Early reflections Behind Direct soundsBy pressing DSP Mode By pressing Surround Mode Available DSP Modes According to the Speaker ArrangementAvailable DSP modes FrontAdjusting the Surround Modes Adjust the effect level JVC Theater Surround adjustmentsLevel you want Adjusting the DAP Modes Press DSP Mode repeatedly untilAdjust the rear speaker output levels Press Sound Adjust the rear speaker outputMode you want appears on the display Press Surround ModeActivating the DSP Modes Press Surround ON/OFFCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverPress the play 3 button on the CD player Automatic Source SelectionOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierOperating Video Components CD changerCassette deck CD recorderTroubleshooting Problem Possible Cause SolutionSpecifications Per channel, min. RMS, driven into 8 ΩHz to 20 kHz with no more than 0.8% total Harmonic distortionFM tuner IHF AM tunerGeneral EN, FR 0301NHMMDWJEIN

RX-6010VBK specifications

The JVC RX-6010VBK is a standout receiver that combines advanced audio technologies with user-friendly features, making it a popular choice for home theater enthusiasts and casual listeners alike. This versatile receiver is designed to deliver outstanding sound performance while providing a host of connectivity options to accommodate various devices.

One of the primary features of the RX-6010VBK is its high powered amplification system, delivering up to 100 watts per channel, which ensures that audio playback remains dynamic and clear, regardless of volume levels. The receiver supports a range of audio formats, including Dolby Digital, DTS, and PCM, enabling it to reproduce surround sound experiences that immerse listeners in their favorite films and music.

The RX-6010VBK is equipped with a sophisticated digital signal processor (DSP) that enhances sound quality by optimizing audio signals for different types of content. This means that whether you're watching an action-packed movie or enjoying a soft ballad, the receiver adjusts the audio output to provide the best possible listening experience.

Connectivity is another highlight of the JVC RX-6010VBK. It features multiple HDMI inputs, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. With support for 4K video upscaling, the receiver ensures that users can enjoy high-definition content with stunning clarity and detail. Additionally, the receiver includes composite and component video inputs, ensuring compatibility with older devices.

The user interface of the RX-6010VBK is intuitive and easy to navigate. The front panel features a clear display and straightforward controls, while a remote control is also included, making it convenient to adjust settings from a distance. The receiver's setup process is simplified by an on-screen graphical interface, allowing users to get started quickly.

One of the more advanced technologies included in the RX-6010VBK is its room calibration feature. This technology uses a built-in microphone to analyze the acoustics of your room, automatically adjusting the audio output to compensate for the unique characteristics of the space. This results in a balanced sound that is tailored to your listening environment.

In terms of aesthetics, the JVC RX-6010VBK boasts a sleek black finish that fits well with modern home entertainment systems. Its compact design makes it easy to integrate into any setup without taking up excessive space.

Overall, the JVC RX-6010VBK receiver stands out as an excellent option for anyone looking to elevate their audio experience. Its combination of powerful amplification, advanced processing technologies, and comprehensive connectivity options make it a valuable addition to any home theater setup. Whether you are a casual viewer or a serious audiophile, the RX-6010VBK is sure to deliver the performance you desire.
Top Page Image Contents