JVC RX-6010VBK manual Connecting the Speakers, AM Antenna Connections, Basic connecting procedure

Page 7

AM Antenna Connections

 

 

 

 

Snap the tabs on the loop into the

ANTENNA

 

slots of the base to assemble the

 

 

FM 75

 

 

AM loop.

 

 

COAXIAL

 

 

 

 

 

 

 

 

 

 

Basic connecting procedure

1

2

3

 

 

 

English

AM

LOOP

1

AM Loop Antenna

AM

EXT

23

1Cut, twist and remove the insulation at the end of each speaker signal cable (not supplied).

2Open the terminal and then insert the speaker signal cable.

3Close the terminal.

Connecting the front speakers

Connect front speakers to the FRONT SPEAKERS terminals.

Outdoor single vinyl-covered wire (not supplied)

Turn the loop until you have the best reception.

Left speaker

Right speaker

Notes:

• If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram.

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop antenna connected.)

FRONT

SPEAKERS

RIGHT

LEFT

Connecting the Speakers

You can connect the following speakers:

•One pair of front speakers to produce normal stereo sound.

•One pair of rear speakers to enjoy the surround effect.

•One center speaker to produce more effective surround effect (to emphasize human voices).

•One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 12.

For each speaker (except for a subwoofer), connect the (+) and (–) terminals on the rear panel to the (+) and (–) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

Connecting the rear and center speakers

Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.

 

CENTER

REAR

 

SPEAKER

SPEAKERS

Center speaker

RIGHT

LEFT

 

 

Left rear

Right rear

 

 

speaker

speaker

 

 

4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents RX-6010VBK Mises en garde, précautions et indications diverses English Français Table of Contents Parts Identification Remote ControlFront Panel Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connectionsDVD player Video component connectionsTo audio Digital connections Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbyFrom the remote control Signal and speaker indicators on the displayPress Muting to mute the sound Listening Only with HeadphonesThrough all speakers and headphones Connected Muting the SoundAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Changing the Source Name Basic SettingsRecording a Source Setting the Subwoofer Information Adjusting the Front Speaker Output BalanceTo select the delay time of the rear speaker output Setting the Speakers for the DSP ModesCenter Delay appears on Display Rear Delay appears on DisplayLFE ATT Low Frequency Effect Attenuator appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect attenuator level Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingPress Sleep repeatedly Storing the Basic Settings AdjustmentsUsing the Sleep Timer Change the input modeUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode What are the DSP Modes? Using the DSP ModesSurround modes Early reflections Behind Direct sounds Available DSP modes according to the input modeReproducing the Sound Field DAP modesFront By pressing DSP Mode By pressing Surround ModeAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes JVC Theater Surround adjustments Adjust the effect levelLevel you want Adjust the rear speaker output Adjusting the DAP ModesPress DSP Mode repeatedly until Adjust the rear speaker output levels Press SoundPress Surround ON/OFF Mode you want appears on the displayPress Surround Mode Activating the DSP ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckProblem Possible Cause Solution TroubleshootingHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.8% totalAM tuner FM tuner IHFGeneral EN, FR 0301NHMMDWJEIN

RX-6010VBK specifications

The JVC RX-6010VBK is a standout receiver that combines advanced audio technologies with user-friendly features, making it a popular choice for home theater enthusiasts and casual listeners alike. This versatile receiver is designed to deliver outstanding sound performance while providing a host of connectivity options to accommodate various devices.

One of the primary features of the RX-6010VBK is its high powered amplification system, delivering up to 100 watts per channel, which ensures that audio playback remains dynamic and clear, regardless of volume levels. The receiver supports a range of audio formats, including Dolby Digital, DTS, and PCM, enabling it to reproduce surround sound experiences that immerse listeners in their favorite films and music.

The RX-6010VBK is equipped with a sophisticated digital signal processor (DSP) that enhances sound quality by optimizing audio signals for different types of content. This means that whether you're watching an action-packed movie or enjoying a soft ballad, the receiver adjusts the audio output to provide the best possible listening experience.

Connectivity is another highlight of the JVC RX-6010VBK. It features multiple HDMI inputs, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. With support for 4K video upscaling, the receiver ensures that users can enjoy high-definition content with stunning clarity and detail. Additionally, the receiver includes composite and component video inputs, ensuring compatibility with older devices.

The user interface of the RX-6010VBK is intuitive and easy to navigate. The front panel features a clear display and straightforward controls, while a remote control is also included, making it convenient to adjust settings from a distance. The receiver's setup process is simplified by an on-screen graphical interface, allowing users to get started quickly.

One of the more advanced technologies included in the RX-6010VBK is its room calibration feature. This technology uses a built-in microphone to analyze the acoustics of your room, automatically adjusting the audio output to compensate for the unique characteristics of the space. This results in a balanced sound that is tailored to your listening environment.

In terms of aesthetics, the JVC RX-6010VBK boasts a sleek black finish that fits well with modern home entertainment systems. Its compact design makes it easy to integrate into any setup without taking up excessive space.

Overall, the JVC RX-6010VBK receiver stands out as an excellent option for anyone looking to elevate their audio experience. Its combination of powerful amplification, advanced processing technologies, and comprehensive connectivity options make it a valuable addition to any home theater setup. Whether you are a casual viewer or a serious audiophile, the RX-6010VBK is sure to deliver the performance you desire.
Top Page Image Contents