JVC Troubleshooting for RX-6010VBK Stereo Receiver
Page 31

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

 

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if

 

 

 

necessary.

 

 

 

 

 

 

The SPEAKERS ON/OFF button is not

Press SPEAKERS ON/OFF button correctly.

 

 

set correctly.

 

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

 

 

 

 

 

 

An incorrect input mode (analog or

Select the correct input mode (analog or

 

 

digital) is selected.

digital).

 

 

 

 

 

 

Connections are incorrect.

Check connections.

 

 

 

For analog connections, see page 5.

 

 

 

For digital connections, see page 7.

 

 

 

 

 

Sound from one speaker only.

Speaker signal cables are not connected

Check speaker wiring and reconnect if

 

 

properly.

necessary.

 

 

 

 

 

 

The balance is set to one extreme.

Adjust the balance properly (see page 11).

 

 

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

 

reception.

 

your dealer.

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

 

An incorrect antenna is used.

Check with your dealer to be sure you have

 

 

 

the correct antenna.

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

 

reception.

 

traffic.

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

1. Press POWER on the front panel to turn off

 

display.

volume.

the receiver.

 

 

 

2. Stop the playback source.

 

 

 

3. Turn on the receiver again, and adjust the

 

 

 

volume.

 

 

 

 

 

 

Speakers are overloaded because of short

Press POWER on the front panel, then check

 

 

circuit of speaker terminals.

the speaker wiring.

 

 

 

If “OVERLOAD” does not disappear, unplug

 

 

 

the AC power cord, then plug it back again.

 

 

 

If speaker wiring is not short-circuited, contact

 

 

 

your dealer.

 

 

 

 

 

“DSP MICON NG” starts flashing on the

The built-in microcomputer is not

Press POWER on the front panel to turn off

 

display.

functioning correctly.

the receiver. After unplugging the power cord,

 

 

 

consult your dealer.

 

 

 

 

 

The STANDBY lamp lights up after

The receiver is overloaded because of a

Press POWER on the front panel to turn off

 

turning on the power, but soon the

high voltage.

the receiver. After unplugging the power cord,

 

receiver turns off (into standby mode).

 

consult your dealer.

 

 

 

 

 

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

 

 

remote sensor on the receiver.

 

 

 

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

 

 

Remote control does not operate

An incorrect remote control operation

Select the correct remote control operation

 

intendedly.

mode is selected.

mode. (See page 26).

 

 

 

 

 

English

28

Page 30 Page 32
Image 31
Page 30 Page 32
Contents RX-6010VBK Mises en garde, précautions et indications diverses English Français Table of Contents Parts Identification Remote ControlFront Panel Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasConnecting the rear and center speakers Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connectionsDVD player Video component connectionsTo audio Digital connections Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbyFrom the remote control Signal and speaker indicators on the displayPress Muting to mute the sound Listening Only with HeadphonesThrough all speakers and headphones Connected Muting the SoundAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Changing the Source Name Basic SettingsRecording a Source Setting the Subwoofer Information Adjusting the Front Speaker Output BalanceTo select the delay time of the rear speaker output Setting the Speakers for the DSP ModesCenter Delay appears on Display Rear Delay appears on DisplayLFE ATT Low Frequency Effect Attenuator appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect attenuator level Selecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingPress Sleep repeatedly Storing the Basic Settings AdjustmentsUsing the Sleep Timer Change the input modeUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode What are the DSP Modes? Using the DSP ModesSurround modes Early reflections Behind Direct sounds Available DSP modes according to the input modeReproducing the Sound Field DAP modesFront By pressing DSP Mode By pressing Surround ModeAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes JVC Theater Surround adjustments Adjust the effect levelLevel you want Adjust the rear speaker output Adjusting the DAP ModesPress DSP Mode repeatedly until Adjust the rear speaker output levels Press SoundPress Surround ON/OFF Mode you want appears on the displayPress Surround Mode Activating the DSP ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder Operating Video ComponentsCD changer Cassette deckProblem Possible Cause Solution TroubleshootingHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.8% totalAM tuner FM tuner IHFGeneral EN, FR 0301NHMMDWJEIN

RX-6010VBK specifications

The JVC RX-6010VBK is a standout receiver that combines advanced audio technologies with user-friendly features, making it a popular choice for home theater enthusiasts and casual listeners alike. This versatile receiver is designed to deliver outstanding sound performance while providing a host of connectivity options to accommodate various devices.

One of the primary features of the RX-6010VBK is its high powered amplification system, delivering up to 100 watts per channel, which ensures that audio playback remains dynamic and clear, regardless of volume levels. The receiver supports a range of audio formats, including Dolby Digital, DTS, and PCM, enabling it to reproduce surround sound experiences that immerse listeners in their favorite films and music.

The RX-6010VBK is equipped with a sophisticated digital signal processor (DSP) that enhances sound quality by optimizing audio signals for different types of content. This means that whether you're watching an action-packed movie or enjoying a soft ballad, the receiver adjusts the audio output to provide the best possible listening experience.

Connectivity is another highlight of the JVC RX-6010VBK. It features multiple HDMI inputs, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. With support for 4K video upscaling, the receiver ensures that users can enjoy high-definition content with stunning clarity and detail. Additionally, the receiver includes composite and component video inputs, ensuring compatibility with older devices.

The user interface of the RX-6010VBK is intuitive and easy to navigate. The front panel features a clear display and straightforward controls, while a remote control is also included, making it convenient to adjust settings from a distance. The receiver's setup process is simplified by an on-screen graphical interface, allowing users to get started quickly.

One of the more advanced technologies included in the RX-6010VBK is its room calibration feature. This technology uses a built-in microphone to analyze the acoustics of your room, automatically adjusting the audio output to compensate for the unique characteristics of the space. This results in a balanced sound that is tailored to your listening environment.

In terms of aesthetics, the JVC RX-6010VBK boasts a sleek black finish that fits well with modern home entertainment systems. Its compact design makes it easy to integrate into any setup without taking up excessive space.

Overall, the JVC RX-6010VBK receiver stands out as an excellent option for anyone looking to elevate their audio experience. Its combination of powerful amplification, advanced processing technologies, and comprehensive connectivity options make it a valuable addition to any home theater setup. Whether you are a casual viewer or a serious audiophile, the RX-6010VBK is sure to deliver the performance you desire.
Top Page Image Contents