JVC RX-6010VBK Operating Video Components, CD changer, Cassette deck, CD recorder, DVD player

English

CD changer

After pressing CD-DISC, you can perform the following operations on a CD changer:

3:	Starts playing.
4:	Returns to the beginning of the current (or previous)
¢:	track.
	Skips to the beginning of the next track.
7:	Stops playing.
8:	Pauses playing. To release it, press 3.
1 – 6, 7/P:	Selects the number of a disc installed in a CD
	changer.

If your CD changer is of 200-disc loading capability (except for XL-MC100 and XL-MC301),

you can do the following operations using the number buttons after pressing CD.

• The 10 button can function as 0.

1.Select a disc number.

2.Then select a track number (always enter two digits).

3.Start playback.

Ex.

Selecting disc number 3, track number 2, and start playback. Press 3, then, 10, 2, then 3.

Selecting disc number 10, track number 5, and start playback. Press 1, 10, then, 10, 5, then 3.

Selecting disc number 105, track number 12, and start playback. Press 1, 10, 5, then 1, 2 then 3.

Cassette deck

After pressing TAPE/CDR, you can perform the following operations on a cassette deck:

3:	Starts playing.
1:	Fast winds the tape from right to left.
Á:	Fast winds the tape from left to right.
7:	Stops operations.
8:	Pauses playing. To release it, press 3.

Note:

Before starting the above operations, make sure that you have

changed the source name correctly. See page 11.

CD recorder

After pressing TAPE/CDR, you can perform the following operations on the CD recorder:

3:	Starts playing.
4:	Returns to the beginning of the current (or previous)
¢:	track.
	Skips to the beginning of the next track.
7:	Stops playing.
8:	Pauses playing. To release it, press 3.

Note:

Before starting the above operations, make sure that you have

changed the source name correctly. See page 11.

Operating Video Components

IMPORTANT:

To operate JVC’s video components using this remote control:

•Some JVC VCRs can accept two types of the control signals — remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR jacks is set to code “A.”

•When using the remote control:

–For the DVD player, TV and VCR operations, aim the remote control directly at the remote sensor on each component, not on the receiver.

VCR

You can always perform the following operations:

VCR:Turns on or off the VCR. (in the POWER section)

After pressing VCR, you can perform the following operations on the VCR:

3:	Starts playing.
1:	Rewinds a tape.
Á:	Fast winds a tape.
7:	Stops operations.
8:	Pauses playing. To release it, press 3.
VCR CH +/–:	Changes the TV channels on the VCR.

DVD player

After pressing DVD, you can perform the following operations on a DVD player:

3: Starts playing.

4: Returns to the beginning of the current (or previous) track.

¢: Skips to the beginning of the next track.

7: Stops playing.

8: Stops playing temporarily. To release it, press 3.

After pressing DVD, these buttons		– SUBWOOFER +
		2
can be used for the DVD menu		5
	EFFECT	– CENTER +
operations.	4	5	6
	5		5
		– REAR•L +
		8	9
		5	MENU
		– REAR•R +

Note:	+10
	ENTER

For detailed menu operations, refer to the

instructions supplied with the discs or the DVD player.

TV

You can always perform the following operations:

TV:Turns on or off the TV. (in the POWER section)

TV/VIDEO: Sets the input mode (either TV or VIDEO).

TV VOL +/–: Adjusts the volume.

TV CH +/–: Changes the channels.

27