JVC RX-6022VSL manual Using DAP Modes and All Channel Stereo

SURROUND MODE

Using DAP Modes and All Channel Stereo

Once you have adjusted the DAP modes and All Channel Stereo, the adjustment is memorized for each source.

•You cannot use the DAP modes and All Channel Stereo if no rear speakers are connected and activated.

•You cannot adjust the effect level for All Channel Stereo.

From the remote control:

It will be convenient for you to use the remote control for adjustments, since you can make adjustments from your listening point.

1Start playing 2 channel software—either analog or Linear PCM—and select the source.

2 Press SURROUND ON/OFF to activate	ON/OFF
Surround mode.	SURROUND

When Surround mode turns on, the last selected Surround mode will be activated.

•Each time you press the button, Surround mode turns on and off alternately.

3 Press SURROUND MODE repeatedly SURROUND

until one of the DAP modes—“LIVE	MODE
CLUB,” “DANCE CLUB,” “HALL,”
“PAVILION”—or “ALL CH STEREO”
appears on the display.

The DSP indicator also lights up on the display.

If you like to adjust sound, go to step 4.

When Surround mode turns on, the last selected Surround mode will be activated.

•Each time you press the button, Surround mode turns on and off alternately.

3 Press SURROUND MODE

repeatedly until one of the DAP modes—“LIVE CLUB,” “DANCE

CLUB,” “HALL,” “PAVILION,”—

or “ALL CH STEREO” appears on the display.

The DSP indicator also lights up on the display.

If you like to adjust sound, go to step 4.

4Adjust the speaker output levels.

1) Press ADJUST repeatedly until one	ADJUST
of the following indications (with the
current setting)* appears on the
display.

REAR L : To adjust the left rear speaker output level (–10 to +10).

REAR R : To adjust the right rear speaker output level (–10 to +10).

CENTER : For “ALL CH STEREO” only—to adjust the center speaker output level

(–10 to +10).

*“0” is the initial setting. If you have already changed the setting, another number (level) will be shown.

Creating Realistic Sound Fields

4 Press SOUND. SOUND

2) Press CONTROL UP 5/DOWN ∞

to adjust the selected speaker

CONTROL

DOWN UP

10 keys are activated for sound adjustments.

5Adjust the speakers output levels (–10 to +10).

•To adjust the left rear speaker level, press REAR•L +/–.

•To adjust the right rear speaker level, press REAR•R +/–.

For “ALL CH STEREO” only:

•To adjust the center speaker level, press CENTER +/–.

REAR L

5 6

REARR

8 9

CENTER

2 3

output levels.

3) Repeat steps 1) and 2) to adjust the

other speaker levels.

5Only for DAP modes: Adjust the DSP effect level.

1)Press ADJUST repeatedly until “EFFECT” (with the current setting)* appears on the display.

ADJUST

6For DAP modes only:

Press EFFECT to select the effect level (1 to 5) you want.

•Each time you press the button, the effect level changes as follows:

EFFECT

4

*“EFFECT 3” is the initial setting. If you have already changed the setting, another setting will be shown.

2) Press CONTROL UP 5/DOWN ∞	DOWN UP
	CONTROL
to select the effect level (1 to 5) you

want.

EFFECT 1	EFFECT 2		EFFECT 3
EFFECT 5		EFFECT 4

As the number increases, the selected mode becomes stronger (normally set it to “EFFECT 3”).

On the front panel:

1Start playing 2 channel software—either analog or Linear PCM—and select the source.

2 Press SURROUND ON/OFF to	SURROUND ON/OFF
activate Surround mode.

•Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5 EFFECT 4

As the number increases, the selected mode becomes stronger (normally set it to “EFFECT 3”).

Note:

You cannot select any DAP mode and All Channel Stereo for Dolby

Digital and DTS Digital Surround.

To cancel DAP modes and All Channel Stereo

Press SURROUND ON/OFF so that “SURROUND OFF” appears on the display. The DSP indicator goes off.

23