JVC RX-6022VSL manual Troubleshooting, Problem Possible Cause Solution

Page 32

Troubleshooting

Use this chart to help you solving daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

The power does not turn on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if necessary.

The SPEAKERS ON/OFF button is not set correctly.

Press SPEAKERS ON/OFF button correctly.

An incorrect source is selected.

Select the correct source.

 

 

Muting is activated.

Press MUTING to cancel the mute.

An incorrect input mode (analog or digital) is selected.

Select the correct input mode (analog or digital).

Connections are incorrect.

Check connections.

 

For analog connections, see page 6.

 

For digital connections, see page 7.

Sound from one speaker only.

Speaker signal cables are not connected properly.

Check speaker wiring and reconnect if necessary.

 

The balance is set to one extreme.

Adjust the balance properly (see page 15).

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

reception.

 

your dealer.

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

An incorrect antenna is used.

Check with your dealer to be sure you have the

 

 

correct antenna.

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

 

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

1.

Press STANDBY/ON

on the front

display.

volume.

 

panel to turn off the receiver.

 

 

2.

Stop the playback source.

 

 

 

3.

Turn on the receiver again, and adjust the

 

 

 

volume.

 

Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

“DSP MICON NG” starts flashing on the

The built-in microcomputer is not

Press STANDBY/ON

on the front panel to

display.

functioning correctly.

turn off the receiver. After unplugging the

 

 

power cord, consult your dealer.

 

 

 

 

The STANDBY lamp lights up after

The receiver is overloaded because of a

Press STANDBY/ON

on the front panel to

turning on the power, but soon the

high voltage.

turn off the receiver. After unplugging the

receiver turns off (into standby mode).

 

power cord, consult your dealer.

 

 

 

 

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

remote sensor on the receiver.

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

Remote control does not work for the source (or other components) you try to operate.

An incorrect remote control operation mode is selected.

Select the correct remote control operation mode (see pages 28 and 29).

30

Page 31 Page 33
Image 32
Page 31 Page 33
Contents RX-6020VBK / RX-6022VSL Mises en garde, précautions et indications diverses Table of Contents Front Panel Remote ControlParts Identification Before Installation Putting Batteries in the Remote Control Checking the Supplied AccessoriesGetting Started Identification / Getting StartedConnecting the FM and AM Antennas AM loop antenna connectionFM antenna connection Supplied FM Standard typeConnecting the Speakers Connecting the front, center and rear speakersSpeaker layout diagram Connecting the subwoofer speakerConnecting Audio/Video Components Analog connections Audio component connectionsVideo component connections VCRConnecting the Power Cord For enjoying DVD Multi Playback ModePlug the power cord into an AC outlet Digital connectionsSelecting the Source to Play Turning On the PowerBasic Operations Adjusting the Volume Basic OperationsTurning Off the Power With the Sleep TimerTurning Off the Sounds Temporarily-MutingBasic Settings Selecting the Analog or Digital Input ModeSetting the Speaker Information Remote On the front panel From the remote controlPress ANALOG/DIGITAL To register whether you have Connected a subwoofer or notBasic Settings Unit with the current setting Appears on the displayPress Control UP /DOWN Select the unitSelect the low frequency effect attenuator level Press Setting repeatedly until LFEDisplay Sound Adjustments Adjusting the Subwoofer Output LevelTuner Operations Tuning in StationsUsing Preset Tuning Selecting the FM Reception Mode Tuner OperationsCreating Realistic Sound Fields Dolby SurroundDTS Digital Surround Typical Multichannel 5.1 ch reproductionDVD Multi Playback Mode DAP Digital Acoustic Processor modesCreating sound field All Channel StereoSelecting Surround modes About Relations between Speaker Layout and Surround ModesTurning on or off Surround modes Activate Surround mode If you like to adjust sound, go to stepPress Surround ON/OFF to Rearl + Rearr +Adjust the speaker output levels 10 to +10 Repeatedly to activate Surround ModePress Control UP Panorama with the currentUsing DAP Modes and All Channel Stereo Using DVD Multi Playback Mode Activating DVD Multi Playback ModeAdjust the speaker output levels Press DVD MultiPress the play 3 button on the CD player Compu Link Remote Control SystemUsing DVD Multi Playback AV Compu Link Remote Control System ConnectionsAutomatic Selection of TV’s Input Mode Automatic Power On/OffAV Compu Link Remote One-Touch Video PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsVideo Components Operating Video ComponentsCassette deck DVD playerTroubleshooting Problem Possible Cause SolutionSpecifications Per channel, min. RMS, driven into 8 ΩHz to 20 kHz with no more than 0.8% total Harmonic distortionDo not service the television yourself Toll Free 1 800Limited Warranty 0302NHMMDWJEIN

RX-6022VSL specifications

The JVC RX-6022VSL is a versatile audio receiver that caters to the demands of both audiophiles and casual listeners. Renowned for its blend of performance, functionality, and aesthetic appeal, the RX-6022VSL has become a favored choice for home theater setups and music enthusiasts alike.

One of the standout features of the RX-6022VSL is its comprehensive support for various audio formats. It offers multiple audio inputs including digital coaxial and optical connections, allowing users to connect a range of devices, from CD players to gaming consoles. This flexibility ensures that all audio sources can be integrated seamlessly into one system.

The RX-6022VSL is equipped with a robust 5.1-channel surround sound capability, supporting Dolby Digital and DTS decoding. This immersive audio experience allows users to enjoy their favorite movies and music with rich, dynamic sound, making it an essential addition to any home theater. The receiver delivers high-powered output with a total power of 100 watts per channel, ensuring that even large rooms can be filled with crisp and powerful audio.

In addition to traditional audio capabilities, the RX-6022VSL features advanced technologies that enhance the listening experience. The inclusion of a built-in AM/FM tuner allows users to access their favorite radio stations easily. Furthermore, the receiver supports various sound enhancement features, such as tone control and balance adjustment, enabling users to customize their audio experience to suit personal preferences.

The user-friendly interface of the RX-6022VSL is designed for ease of use. A dual-front display provides quick access to controls, while an intuitive remote control allows for convenient operation from a distance. Additionally, the receiver is equipped with an easy-to-use setup wizard that guides users through the initial configuration process, ensuring a hassle-free installation.

Design-wise, the JVC RX-6022VSL boasts a sleek and modern aesthetic, making it a stylish addition to any entertainment center. With an elegant black finish and well-organized front panel, it not only performs well but also complements the decor of any living space.

Overall, the JVC RX-6022VSL is a powerful and adaptable audio receiver that combines essential features with advanced technology. Its ability to provide high-quality sound, multiple connectivity options, and user-friendly design makes it a valuable choice for anyone looking to elevate their audio experience at home.
Top Page Image Contents