JVC RX-6000VBK, RX-6008VBK Adjusting the Subwoofer Output Level, Attenuating the Input Signal

Page 13

English

Adjusting the Subwoofer Output Level

You can adjust the subwoofer output level if you have selected “YES” for the “SUBWOOFER” (see page 11).

Once it has been adjusted, the receiver memorizes the adjustment.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel:

 

1. Press ADJUST repeatedly until

ADJUST

“SUBWFR LEVEL” appears on

 

the display.

 

•Once you have pressed ADJUST, MULTI CURSOR %/ Þ can be also used for selecting “SUBWFR LEVEL.”

•The display changes to show the current setting.

2.

Press MULTI CURSOR @/ #to

MULTI CURSOR

 

 

 

 

adjust the subwoofer output level

 

 

 

(–10 dB to +10 dB).

 

 

From the remote control:

SOUND

 

 

 

 

1.

Press SOUND.

 

 

 

The 10 keys are activated for sound adjustments.

 

2.

Press SUBWOOFER –/+ to adjust

– SUBWOOFER +

 

the subwoofer output level (–10 dB

2

3

 

to +10 dB).

 

 

Attenuating the Input Signal

When the input level of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

On the front panel ONLY:

 

Press and hold INPUT ATT. (ONE TOUCH

INPUT ATT.

 

ONE TOUCH OPERATION/

OPERRATION) so that the ATT indicator

 

lights up on the display.

 

•Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).

Notes:

•This function is available only for the sources connected using the analog terminals.

•This function does not take effect when digital input is selected.

Reinforcing the Bass

With this Bass Boost function, you can boost the bass level.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press ADJUST repeatedly until

ADJUST

“BASSBOOST” (with the current

 

setting) appears on the display.

 

•Once you have pressed ADJUST, MULTI CURSOR % / Þ can be also used for selecting “BASSBOOST.”

2. Press MULTI CURSOR @/ #to

MULTI CURSOR

switch this function “ON” or

 

“OFF.”

 

• When this function is switched “ON,” the BASS BOOST indicator on the display lights up.

Note:

The Bass Boost function affects the front speaker sounds only.

Adjusting the Tone

You can adjust the treble and bass sounds as you like.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press ADJUST repeatedly until

ADJUST

 

“BASS” or “TREBLE” appears on

 

the display.

 

•Once you have pressed ADJUST, MULTI CURSOR %/ Þ can be also used for selecting “BASS” or “TREBLE.”

•Select “BASS” to adjust the bass sound level.

•Select “TREBLE” to adjust the treble sound level.

2. Press MULTI CURSOL @/ #to

MULTI CURSOR

adjust the bass or treble sound

 

level within the range of –10 to

 

+10.

 

•Each time you press the button, the sound level changes by ± 2 steps.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents RX-6000VBK / RX-6008VBK Errata Sheet For U.S.A Table of Contents Parts Identification Front Panel Remote Control@ Û # Ü To use the Multi Cursor buttons w on the front panelConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers Connecting the rear and center speakersConnecting the subwoofer speaker Connecting Audio/Video ComponentsAnalog connections Audio component connectionsDVD player Video component connectionsDBS tuner If your audio components have an AV Compu Link terminalPutting Batteries in the Remote Control Connecting the Power CordOn the back of the remote control, remove the battery cover Plug the power cord into an AC outletTo turn off the power into standby mode To turn on the power, press PowerFrom the remote control On the front panelMuting the Sound Selecting the Front SpeakersAttenuating the Input Signal Adjusting the Subwoofer Output LevelAdjusting the Tone Reinforcing the BassAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Recording a Source Changing the Source NameRear Delay appears on Display Setting the Speakers for the DSP ModesCenter SPK Center Select the appropriate item aboutLow Frequency Effect Attenuator Setting Crossover Frequency SettingDynamic Range Compression Setting Select the low frequency effect Attenuator levelSelect an appropriate setting Digital Input Digital in Terminal SettingSelecting the Analog or Digital Input Mode Digital 2 terminal setting Digital 1 terminal settingUsing the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed above Using Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Press 10 keys to select a preset Select a preset channel stationPress FM/AM Channel number3D-PHONIC modes Using the DSP ModesDAP modes Surround modes Headphones modeDolby Surround Dolby Digital and Dolby Pro Logic DTS Digital SurroundFront Available DSP Modes According to the Speaker ArrangementAdjusting the DAP Modes Headphones mode Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes Appears on the display.SURROUND JVC Theater Surround adjustmentsPress Test to check the speaker PRO LOGIC, Dolby Digital or DTS SurroundPress Multi Cursor @/ #to select the effect level Press Surround so that Activating the DSP ModesLamp next to the button lights up Select and play a sound sourceRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemSame time Synchronized RecordingIf the AV Compu Link terminal AV Compu Link Remote Control SystemOn the TV is RECEIVER/AMP If the AV Compu Link terminal on the TV is AV Compu Link EXAutomatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play One-Touch DVD PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsTurntable CD playerCassette deck CD player-changerMD recorder DVD playerProblem Possible Cause Solution TroubleshootingPer channel, min. RMS, driven into 8 Ω SpecificationsHz to 20 kHz with no more than 0.8% total Harmonic distortionAM tuner FM tuner IHFGeneral Valley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 1299HIMMDWJEIN

RX-6000VBK, RX-6008VBK specifications

The JVC RX-6008VBK and RX-6000VBK are integral components of JVC's renowned line of receivers, designed to elevate home audio experiences with their impressive features and advanced technologies. These models cater to both casual listeners and audiophiles alike, offering a robust combination of performance and versatility.

One of the standout features of the RX-6008VBK and RX-6000VBK is their powerful amplification system. Both receivers deliver a significant output power, enabling them to drive speakers effectively and provide a rich, immersive sound experience. With 100 watts per channel, they can fill larger rooms with high-quality audio, bringing movies, music, and games to life.

These receivers are also equipped with multi-channel processing capabilities, allowing users to set up surround sound systems effortlessly. The RX-6008VBK and RX-6000VBK support various surround sound formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy high-definition audio from their home theater systems.

Another notable characteristic is the incorporation of JVC's proprietary technologies. The receivers feature the Audyssey room correction technology, which calibrates the sound based on the acoustics of the room, ensuring optimal audio performance across different environments. This technology tailors the audio output to accommodate any room, delivering clear and balanced sound.

Connectivity is a significant aspect of the RX-6008VBK and RX-6000VBK. Both models provide an array of inputs, including HDMI, optical, and analog connections, making it easy to connect multiple devices such as gaming consoles, Blu-ray players, and streaming devices. The HDMI inputs support 4K Ultra HD passthrough, ensuring compatibility with the latest video formats, enabling users to enjoy stunning visual clarity.

Moreover, these receivers come with built-in Bluetooth capabilities, allowing users to stream audio directly from their smartphones or tablets. This wireless feature enhances convenience, offering an easy way to enjoy music without the hassle of cables.

In terms of design, the JVC RX-6008VBK and RX-6000VBK boast sleek and modern aesthetics, fitting seamlessly into any home decor. The user-friendly interface and remote control facilitate effortless navigation through various settings and playback options.

Ultimately, the JVC RX-6008VBK and RX-6000VBK are exceptional audio receivers, combining performance, advanced technologies, and user-friendly features. Whether for casual listening or an immersive home theater setup, these models stand out as reliable choices for enhancing any audio experience.
Top Page Image Contents