JVC XM-448BK manual For U.S.A

Page 2

Warnings, Cautions and Others

 

 

CAUTION

 

 

 

RISK OF ELECTRIC SHOCK

 

 

 

DO NOT OPEN

 

 

 

 

 

 

 

 

 

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK.

 

DO NOT REMOVE COVER (OR BACK)

 

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Caution –– POWER switch!

Disconnect the mains plug to shut the power off completely. The POWER switch in any position does not disconnect the mains line. The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

1.CLASS 1 LASER PRODUCT

2.DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

3.CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.

– G-1 –

Page 1 Page 3
Image 2
Page 1 Page 3
Contents XM-448BK For U.S.A For safe use, observe the following WelcomeImportant cautions Table of Contents Front panel STOP/CANCEL buttonParts Index DisplayInside panel Remote control unitPower button Buttons on the Inside Panel Play Mode buttons Display buttonsRemote control batteries Setting up the SystemSupplied accessories Operating the remote control unitExample Amplifier/Tuner Signal cable connectionsConnection Audio pin cordsPower Off Turning the Power On and OffPower On AC power cord connectionPlayback Continuous playbackSearch play Using headphonesTo select a track Program playback Using the display modeTo switch the display information To change the brightness of the displaySelect desired track numbers to be programmed. Main unit Remote control unitSelect Program Play mode. Main unit Random playback Repeat playback To cancel Random Play mode In Stop mode Main unitTo cancel repeat playback To repeat random playbackThings to know before recording RecordingRecording operation Play the source to be recorded To stop recordingTrack marking To adjust the analog input levelTo display the remaining recording time Editing Functions MD editing functionsAssigning titles When using the remote control unitCombining editing functions Play a track to be divided Press SET on the main unit or on the remote control unitDividing a track Divide Joining tracks Join Decrements by Press Enter on the main unit or on the remote control unitSelect a track to be joined with the previous track Moving a track Move Select a track number to be moved, then press SETTo select Erase Press Edit on the main unit or on the remote control unitErasing a track Erase Blinks Blinks BlinksControl unit to eject the MD Select a track number to be erased, then press SETPress 0 on the main unit or on the cover panel the remote Erasing all tracks in an MD ALL Erase Load a recorded MD Press Title To assign a title using the buttons on the main unitAssigning the disc title and track titles Press SETPress 0 to eject the MD Available symbolsPress Enter To make a correction or change the titleInput the disc or track title To assign a track title during playback or recording Input the track title nameLinked Operation of the Other Optional Components Compu Text Compu Link Connection with receiver or amplifierConnection to CD player or CD changer CD player1st generation 2nd generation Rule on Digital CopyingScms Serial Copy Management System Two disc types About MD Mini DiscRole of the cartridge Playback-only MDSound skip guard memory Utoc User Table Of ContentsAtrac Adaptive TRansform Acoustic Coding MD handling precautions Handling MDsMD Messages Messages Description TreatmentSymptom Cause MD RestrictionsTroubleshooting Symptom Cause TreatmentHOW to Locate Your JVC Service Center Limited Warranty AUDIO-1 Specifications Digital
Top Page Image Contents