JVC XM-448BK manual To adjust the analog input level, To display the remaining recording time

Page 18

To adjust the analog input level ——————————

The input level should be adjusted before recording the analog input.

1In Rec/Pause mode, start playing the source for level adjustment. The level indicators show the input levels.

2Turn the jog dial on the main unit to the right or left or press ¢or 4on the remote

control unit to increase or decrease the recording level.

As you adjust the recording level, “VOL. –10” will appear, for example. You can adjust

the recording level between VOL.–50 and VOL.0 (–50 dB and 0 dB), or to VOL. – – –

(below –50 dB).

OR

L

40 30 20 15 10 6 3 0 dB

R

•Normally the input level should be adjusted so that the segments for 0 dB blink at the peak level.

•When the input level is too high, the OVER indicator will light up, resulting in distorted recording.

OR

MODE

To display the remaining recording time ——————

In Rec/Pause or during recording, press DISPLAY/CHARACTER on the main unit or MODE on the remote control unit.

Each press of the button switches the elapsed recording time display and remaining recording time display alternately.

remaining recording time

Track marking ———————————————————

The track numbers on the MD are marked at the beginning of each track. The track numbers are identified by these “track markings” and each section between two track markings is considered as a track.

OR

SET

TRACK MARKING

For analog input:

When the point you want to record a track marking comes during recording, press SET on the main unit or on the inside panel of the remote control unit. This operation records a track marking at the point where the button is pressed.

To use automatic track marking:

Press TRACK MARKING on the remote control unit to select “AUTO”.

•A track marking is automatically recorded every time a blank of more than 3 seconds is detected.

To cancel automatic track marking, press TRACK MARKING on the remote control unit again to select “MANUAL”.

For digital input:

When tracks are recorded from a CD player by digital input, track markings are recorded automatically at the points where the CD tracks change.

16

Image 18

Contents XM-448BK For U.S.A Welcome Important cautionsFor safe use, observe the following Table of Contents Front panel STOP/CANCEL buttonParts Index DisplayInside panel Remote control unitPower button Buttons on the Inside Panel Play Mode buttons Display buttonsRemote control batteries Setting up the SystemSupplied accessories Operating the remote control unitExample Amplifier/Tuner Signal cable connectionsConnection Audio pin cordsPower Off Turning the Power On and OffPower On AC power cord connectionPlayback Continuous playbackUsing headphones To select a trackSearch play Program playback Using the display modeTo switch the display information To change the brightness of the displayRemote control unit Select Program Play mode. Main unitSelect desired track numbers to be programmed. Main unit Random playback Repeat playback To cancel Random Play mode In Stop mode Main unitTo cancel repeat playback To repeat random playbackRecording Recording operationThings to know before recording Play the source to be recorded To stop recordingTo adjust the analog input level To display the remaining recording timeTrack marking Editing Functions MD editing functionsWhen using the remote control unit Combining editing functionsAssigning titles Press SET on the main unit or on the remote control unit Dividing a track DividePlay a track to be divided Joining tracks Join Press Enter on the main unit or on the remote control unit Select a track to be joined with the previous trackDecrements by Moving a track Move Select a track number to be moved, then press SETTo select Erase Press Edit on the main unit or on the remote control unitErasing a track Erase Blinks Blinks BlinksSelect a track number to be erased, then press SET Press 0 on the main unit or on the cover panel the remoteControl unit to eject the MD Erasing all tracks in an MD ALL Erase Load a recorded MD Press Title To assign a title using the buttons on the main unitAssigning the disc title and track titles Press SETPress 0 to eject the MD Available symbolsPress Enter To make a correction or change the titleInput the disc or track title To assign a track title during playback or recording Input the track title nameLinked Operation of the Other Optional Components Compu Text Compu Link Connection with receiver or amplifierConnection to CD player or CD changer CD playerRule on Digital Copying Scms Serial Copy Management System1st generation 2nd generation Two disc types About MD Mini DiscRole of the cartridge Playback-only MDUtoc User Table Of Contents Atrac Adaptive TRansform Acoustic CodingSound skip guard memory MD handling precautions Handling MDsMD Messages Messages Description TreatmentSymptom Cause MD RestrictionsTroubleshooting Symptom Cause TreatmentHOW to Locate Your JVC Service Center Limited Warranty AUDIO-1 Specifications Digital