JVC XM-448BK manual Joining tracks Join

Page 22

5Fine-adjust the track marking position.

Turn the jog dial on the main unit or press < / 4 or ¢/ > on the remote control

 

unit.

 

The track marking position can be fine-adjusted in the range of ±128 positions (approx.

OR

±8 sec.).

As you adjust, the track marking is displaced slightly and the 4-second section from the

 

newly divided point will be played repeatedly.

•After completing the fine-adjustment, go to step 6.

•To cancel the current track marking position, press 7STOP/CANCEL on the main unit or CANCEL on the remote control unit and repeat from step 3.

6 Press ENTER on the main unit or on the remote control

OR

ENTER

unit.

1

2

3 4 5

 

 

The change made above is entered

6

7

 

 

 

 

 

 

temporarily in memory. The display shows “EDITING” and the TOC indicator lights up.

TOC indicator:

The TOC indicator shows that the MD has new data that should be memorized. The data writing operation is done by ejecting the MD or by turning the power off. Before the MD is ejected or the power is turned off, “UTOCwriting” is displayed until the data is completely written.

 

7

Press 0 on the main unit or on the cover panel of the

OR

remote control unit to eject the MD.

The data in memory is written in the MD before it is ejected.

The display shows “UTOCwriting” during MD writing operation.

•Be careful not to apply impact to the MD recorder during writing temporarily stored data into the MD. Otherwise the recording may not be able to play later.

•The data in memory is written in the MD also when the power is turned off while “EDITING” is being displayed.

To cancel editing:

Press EDIT repeatedly on the main unit or on the remote control unit before pressing

ENTER in step 6.

To restore the original track from the divided tracks:

Use the JOIN editing function mentioned below.

Joining tracks (JOIN)

EDIT

OR

Two adjacent tracks can be joined into a single track by deleting an unnecessary track marking. This also makes it possible to join more than two tracks into a single track or a piece of music divided into multiple tracks into a single piece. The track numbers after the joined tracks are renumbered automatically.

1Press EDIT on the main unit or on the remote control unit to select “JOIN”.

The JOIN indicator lights up.

Each press of the button switches the editing functions as follows.

DIVIDE JOIN MOVE ERASE ALL ERASE

Canceled

(MD total playing time display or Disc title)

Blinks

20

1 2 3 4 5

6

Page 21 Page 23
Image 22
Page 21 Page 23
Contents XM-448BK For U.S.A Important cautions WelcomeFor safe use, observe the following Table of Contents Front panel STOP/CANCEL buttonParts Index DisplayInside panel Remote control unitPower button Buttons on the Inside Panel Play Mode buttons Display buttonsRemote control batteries Setting up the SystemSupplied accessories Operating the remote control unitExample Amplifier/Tuner Signal cable connectionsConnection Audio pin cordsPower Off Turning the Power On and OffPower On AC power cord connectionPlayback Continuous playbackTo select a track Using headphonesSearch play Program playback Using the display modeTo switch the display information To change the brightness of the displaySelect Program Play mode. Main unit Remote control unitSelect desired track numbers to be programmed. Main unit Random playback Repeat playback To cancel Random Play mode In Stop mode Main unitTo cancel repeat playback To repeat random playbackRecording operation RecordingThings to know before recording Play the source to be recorded To stop recordingTo display the remaining recording time To adjust the analog input levelTrack marking Editing Functions MD editing functionsCombining editing functions When using the remote control unitAssigning titles Dividing a track Divide Press SET on the main unit or on the remote control unitPlay a track to be divided Joining tracks Join Select a track to be joined with the previous track Press Enter on the main unit or on the remote control unitDecrements by Moving a track Move Select a track number to be moved, then press SETTo select Erase Press Edit on the main unit or on the remote control unitErasing a track Erase Blinks Blinks BlinksPress 0 on the main unit or on the cover panel the remote Select a track number to be erased, then press SETControl unit to eject the MD Erasing all tracks in an MD ALL Erase Load a recorded MD Press Title To assign a title using the buttons on the main unitAssigning the disc title and track titles Press SETPress 0 to eject the MD Available symbolsPress Enter To make a correction or change the titleInput the disc or track title To assign a track title during playback or recording Input the track title nameLinked Operation of the Other Optional Components Compu Text Compu Link Connection with receiver or amplifierConnection to CD player or CD changer CD playerScms Serial Copy Management System Rule on Digital Copying1st generation 2nd generation Two disc types About MD Mini DiscRole of the cartridge Playback-only MDAtrac Adaptive TRansform Acoustic Coding Utoc User Table Of ContentsSound skip guard memory MD handling precautions Handling MDsMD Messages Messages Description TreatmentSymptom Cause MD RestrictionsTroubleshooting Symptom Cause TreatmentHOW to Locate Your JVC Service Center Limited Warranty AUDIO-1 Specifications Digital
Top Page Image Contents