Weider 9300 PRO user manual Cable Assembly

Page 13

CABLE ASSEMBLY

24.Identify the Rear Cable (86)Ñthis is the shortest Cable. Slide one end of the Rear Cable onto the 5/16Ó x 3Ó Bolt (91) on the Top Frame (2). Thread a 5/16Ó Nylon Jam Nut (90) onto the Bolt. Do not fully tighten the Jam

Nut; leave enough room between the two Jam Nuts for the Cable to pivot.

25.See the inset drawing. Attach a 3 1/2Ó Pulley (82) and a Cable Trap (80) to the upper hole in the Large ÒUÓ Bracket (83) with a 3/8Ó x 2Ó Bolt (50) and a 3/8Ó Nylon Locknut (42). Be sure that the Cable Trap is inside the Large ÒUÓ Bracket. Note: This may come pre-assembled.

Route the Rear Cable (86) through the Large ÒUÓ Bracket (83) and the 3 1/2Ó Pulley (82).

Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

26.Wrap the Rear Cable (86) around a 3 1/2Ó Pulley (82). Attach the Pulley to the Top Frame (2) with a 3/8Ó x 2Ó Bolt (50) and a 3/8Ó Nylon Locknut (42). The Cable must be routed in the direction shown.

27.Attach the Rear Cable (86) to a Small ÒUÓ Bracket (32) with a 1/4Ó Washer (37) and a 1/4Ó Nylon Locknut (44). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.

Attach the Small ÒUÓ Bracket (32) to the indi- cated Weight Tube (25) with a 5/16Ó x 1 3/4Ó Bolt (68) and a 5/16Ó Nylon Locknut (40).

13

24

 

 

 

 

 

90

91

 

 

 

 

 

86

 

 

 

2

 

25

 

 

 

 

86

 

 

 

80

82

86

 

 

 

 

 

 

42

50

 

 

 

 

 

83

 

82

 

 

83

 

 

 

26

 

 

2

 

 

42

 

 

50

 

 

 

 

 

 

82

 

 

 

86

27

 

 

86

 

 

 

 

 

32

40

 

 

 

 

 

68

 

 

 

 

37

 

 

 

44

 

 

 

25

32

 

86

 

 

 

 

 

 

37

 

 

 

44

 

Image 13
Contents Model No. WESY29100 Serial No QUESTIONS?Customer HOT Line Limited Warranty Table of ContentsImportant Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyDo not tighten the Nylon Locknuts yet Òframe Assembly BAG TWO.ÓLocknuts yet Weight Tubes are in the pin grooves in the upper Weights Òarm ASSEMBLY.Ó Frame Assembly ARM AssemblyARM Assembly ARM Assembly Cable Assembly Cable Assembly Cable Assembly Cable Trap is turned to hold the Cable Place Identify the Press Cable 87Ñthis isCable Assembly Trap is turned to hold the Cable in place Cable Assembly Be sure that the Cable Trap is in the indi- cated position Òseat ASSEMBLY.Ó Seat AssemblyMisc Changing the Weight Setting HOW to USE the Training SystemAttaching the AB Strap to the AB Pulley Station Adjusting the Curl PADAttaching the LEG Lever to the LOW Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceCable Diagrams Page Page Part Identification CHARTÑModel No. WESY29100 Page 7/8 Plastic Bushing Qty Description Part LISTÑModel No. WESY29100Exploded DRAWINGÑModel No. WESY29100 Ordering Replacement Parts