Weider 8510 Locknut 3. Do not overtighten the Nylon, Locknut. The Leg Lever must be able to

Page 14

SEAT ASSEMBLY

26.Attach the Backrest (41) to the Front Upright (42) with two 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó Flat Washers (10).

27. Press a 1 1/2Ó Square Inner Cap (32) into the

Seat Frame (36).

Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the

center hole in the Seat Plate (37). Attach the

Seat Plate to the Seat (13) with two 1/4Ó x

1/2Ó Screws (18).

Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the

indicated hole in the Seat Frame (36).

Tighten a 1/4Ó Nylon Locknut (2) with a 1/4Ó

Flat Washer (10) onto the Carriage Bolt.

Attach the other end of the Seat (13) to the

Seat Frame (36) with a 1/4Ó Flat Washer (10)

and the 1/4Ó x 2Ó Screw (24).

28. Press a 1 1/2Ó Square Inner Cap (32) into the

Leg Lever (29).

Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach

the Leg Lever (29) to the Seat Frame (36)

with the 5/16Ó x 2 1/4Ó Bolt and a 5/16Ó Nylon

Locknut (3). Do not overtighten the Nylon

26

42

41

43 10

27

13

	38
	37	32
		32
		18
36
24	10
24		2
		2

28

36

3

2

Locknut. The Leg Lever must be able to

pivot freely.

Insert the 5/16Ó x 2Ó Eyebolt (35) into the Leg

Lever (29) from the direction shown. Tighten

a 5/16Ó Nylon Locknut (3) with a 5/16Ó Flat

Washer (8) onto the Eyebolt.

LubricateÐ33

35

32

29

8

3

14

Image 14

Contents Customer HOT Line QUESTIONS?Model No. WESY85101 Serial No Patent PendingTable of Contents Limited WarrantyImportant Precautions Assembled Dimensions Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyChart located in the center of this manual Nylon Locknuts yet Tighten all Nylon Locknuts used in steps 1 throughThat the pulleys are on the indicated side Plastic Bushings should fit onto each endIndicated tube in the Base. Be sure ARMArm with the Left Arm 47 refer to step On each Arm. Arm identification is veryImportant for step To identify the Right Arm. Be sure thatCable Assembly Cable Assembly Crossbar Inset shows view From other sideCable Assembly Pivot freely Locknut 3. Do not overtighten the NylonLocknut. The Leg Lever must be able to Seat Assembly High Pulley Butterfly Adjustment Changing the Weight SettingAttaching the LEG Lever to the LOW Pulley Station Weight Resistance ChartAttaching and Removing the Seat TROUBLE-SHOOTING and Maintenance Tightening the CablesShort Cable Cable DiagramLong Cable 23 TOP View Page Part LISTÑModel No. WESY85101 Key No. Qty DescriptionExploded DRAWINGÑModel No. WESY85101 Page Page Page Ordering Replacement Parts