25. Remove the 3/8” x 2” Bolt (12), the 3/8” Nylon | 25 |
|
|
|
|
Locknut (21), the 4 1/2” Pulley (84), and the Metal |
|
|
|
| |
|
|
|
|
| |
Cable Trap (97) from the lower ends of the Pulley |
|
|
|
|
|
Plates (20). Wrap the Low Cable (19) over the |
|
|
|
|
|
Pulley, and reattach the Pulley and the Metal |
|
| 20 |
|
|
Cable Trap to the Pulley Plates with the Bolt and |
|
| 12 |
|
|
the Nylon Locknut. Make sure that the Bolt is |
|
| 21 |
| |
|
|
|
| ||
inserted into the indicated holes in the Pulley |
| 97 |
|
|
|
Plates. In addition, make sure that the Cable is |
|
|
|
| |
| 84 |
|
|
| |
in the groove of the Pulley and that the Cable |
|
|
|
| |
|
|
|
|
| |
Trap is turned to hold the Cable in place. |
|
|
|
|
|
|
| 19 |
|
|
|
26. Remove the 3/8” x 2” Bolt (12), the 3/8” Nylon | 26 |
|
|
|
|
Locknut (21), the 3 1/2” Pulley (15), and the |
|
|
|
| |
|
|
|
|
| |
Cable Trap (66) from the Long |
|
| 19 |
|
|
Wrap the Low Cable (19) around the Pulley (15) |
|
|
|
| |
as shown, and reattach the Pulley and the Cable |
|
|
|
|
|
Trap to the Long |
|
|
|
|
|
Nylon Locknut. Make sure that the Cable Trap |
| 15 |
|
|
|
is turned to hold the Cable in place. |
|
|
|
| |
|
|
|
|
| |
|
| 21 |
| 66 |
|
|
|
|
|
| |
|
| 57 |
| 12 |
|
27. Remove the 3/8” Nylon Locknut (21) from the | 27 |
|
|
|
|
indicated 3/8” x 2 1/2” Bolt (7); do not remove |
|
|
|
| |
|
|
|
|
| |
the Bolt. Slide the end of the Low Cable (19) |
|
|
|
|
|
onto the end of the Bolt, and retighten the Nylon |
|
|
|
|
|
Locknut onto the Bolt. Do not overtighten the |
|
|
|
|
|
Nylon Locknut; the Cable must be able to |
|
|
|
|
|
pivot freely. |
| 7 |
|
|
|
| 21 |
|
|
|
|
| 19 |
|
|
|
|
28. Identify the Press Cable (58). Attach the loop on |
|
|
|
|
|
the end of the Press Cable to the Leg Lever (29) | 28 |
|
| 29 |
|
with a 3/8” x 3” Bolt (93), the 1/2” x 1/2” Bushing |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
(96), a 3/8” Washer (9), and a 3/8” Nylon Locknut | 58 | 77 |
| 33 |
|
(21). Make sure that the cable end is oriented |
|
|
| ||
as shown in the inset drawing. Do not over- | 66 |
|
| 21 | 21 |
tighten the Nylon Locknut; the Cable must be |
|
| 9 | ||
|
|
| |||
|
|
|
| ||
able to pivot freely. |
|
|
| 9 | 29 |
|
|
|
| 96 | |
Route the Press Cable (58) under a 3 1/2” Pro |
|
|
|
| |
16 |
|
|
| 96 | |
Pulley (77). Attach the Pulley and a Cable Trap |
|
|
| ||
93 |
|
|
| ||
(66) to the Seat Frame (36) with a 3/8” x 3 1/2” |
|
|
| ||
|
|
| 58 | Cable | |
Bolt (16), a 3/8” Washer (9), and a 3/8” Nylon |
|
|
| ||
|
|
|
| End | |
Jamnut (33). Make sure the Cable is between |
| 36 |
|
| |
|
|
|
| ||
the Pulley and the Cable Trap, and the Cable |
|
|
| 93 | |
|
|
|
| ||
Trap is turned to hold the Cable in place. |
|
|
|
|
|
| 13 |
|
|
|
|